SMD marking

6661

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables.

The only part printed 6661 in our tables

AON6661

What it is: Complementary MOSFET pair (N-channel and P-channel)
Maker: Alpha & Omega Semiconductor
Package: Not recorded
Pins: Not recorded
Details: Complementary N+P MOSFET pair (20-60 V)
Source: From the manufacturer's datasheet

Is it dead?

Diode range, part lifted. Test drain to source first, then short gate to source and test again. Test each MOSFET on its own pins, as the datasheet's pinout gives them.

Working, it reads

One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.

Dead, it reads

Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.

On the board:: On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:: If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:: The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Datasheet

8 more parts have codes that begin with 6661

Codes that begin with 6661

For a marking with its end worn or burnt off. Each one shows its full printed code.

MOSFET, all Alpha & Omega Semiconductor.

AOUS66616printed 66616SOIC-8
Printed 66616. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Alpha & Omega Semiconductor
Package
SOIC-8
Pins
8
Details
Medium-voltage (40-400 V) MOSFET
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AOUS66616, opens in a new tab
7 more parts have no package on record
- AONS66612printed 66612
  Printed 66612. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  MOSFET
  Maker
  Alpha & Omega Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Details
  Medium-voltage (40-400 V) MOSFET
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted. Test drain to source first, then short gate to source and test again.
  Working, it reads
  One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
  Dead, it reads
  Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  The gate reads low to source or drain: gate shorted.
  No body diode at all: failed open.
  On the board:
  On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor AONS66612, opens in a new tab
- AONS66613printed 66613
  Printed 66613. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  MOSFET
  Maker
  Alpha & Omega Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Details
  Medium-voltage (40-400 V) MOSFET
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted. Test drain to source first, then short gate to source and test again.
  Working, it reads
  One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
  Dead, it reads
  Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  The gate reads low to source or drain: gate shorted.
  No body diode at all: failed open.
  On the board:
  On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor AONS66613, opens in a new tab
- AONS66614printed 66614
  Printed 66614. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  MOSFET
  Maker
  Alpha & Omega Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Details
  Medium-voltage (40-400 V) MOSFET
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted. Test drain to source first, then short gate to source and test again.
  Working, it reads
  One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
  Dead, it reads
  Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  The gate reads low to source or drain: gate shorted.
  No body diode at all: failed open.
  On the board:
  On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor AONS66614, opens in a new tab
- AONS66615printed 66615
  Printed 66615. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  MOSFET
  Maker
  Alpha & Omega Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Details
  Medium-voltage (40-400 V) MOSFET
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted. Test drain to source first, then short gate to source and test again.
  Working, it reads
  One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
  Dead, it reads
  Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  The gate reads low to source or drain: gate shorted.
  No body diode at all: failed open.
  On the board:
  On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor AONS66615, opens in a new tab
- AONS66615Tprinted 66615T
  Printed 66615T. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  MOSFET
  Maker
  Alpha & Omega Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Details
  Medium-voltage (40-400 V) MOSFET
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted. Test drain to source first, then short gate to source and test again.
  Working, it reads
  One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
  Dead, it reads
  Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  The gate reads low to source or drain: gate shorted.
  No body diode at all: failed open.
  On the board:
  On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor AONS66615T, opens in a new tab
- AONS66617printed 66617
  Printed 66617. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  MOSFET
  Maker
  Alpha & Omega Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Details
  Medium-voltage (40-400 V) MOSFET
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted. Test drain to source first, then short gate to source and test again.
  Working, it reads
  One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
  Dead, it reads
  Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  The gate reads low to source or drain: gate shorted.
  No body diode at all: failed open.
  On the board:
  On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor AONS66617, opens in a new tab
- AOTL66610printed 66610
  Printed 66610. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  MOSFET
  Maker
  Alpha & Omega Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Details
  Medium-voltage (40-400 V) MOSFET
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted. Test drain to source first, then short gate to source and test again.
  Working, it reads
  One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
  Dead, it reads
  Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  The gate reads low to source or drain: gate shorted.
  No body diode at all: failed open.
  On the board:
  On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor AOTL66610, opens in a new tab

Open this in the search to correct a character or try another package.