WhatSMD: identify an unknown SMD component

14 parts are printed H

Not sure which one you have?

Answer up to 4 quick questions and these 14 parts are ranked, with a meter test that settles it. It works on a dead part too.

AOC2421P-channel MOSFET, Alpha & Omega SemiconductorP-channel MOSFETAlpha & Omega Semiconductor
What it is
P-channel MOSFET
Maker
Alpha & Omega Semiconductor
Package
Not recorded
Pins
Not recorded
Details
P-channel MOSFET (8-60 V)
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the drain, black on the source: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AOC2421, opens in a new tab
AOCA24106CDual N-channel MOSFET, Alpha & Omega SemiconductorDual N-channel MOSFETAlpha & Omega Semiconductor
What it is
Dual N-channel MOSFET
Maker
Alpha & Omega Semiconductor
Package
Not recorded
Pins
Not recorded
Details
Common-drain dual N-channel battery MOSFET
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again. Test each MOSFET on its own pins, as the datasheet's pinout gives them.
Working, it reads
Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AOCA24106C, opens in a new tab
AOZ1353LI-04Load switch, Alpha & Omega SemiconductorLoad switchAlpha & Omega Semiconductor
What it is
Load switch
Maker
Alpha & Omega Semiconductor
Package
Not recorded
Pins
Not recorded
Details
USB Type-C protection switch
Source
From the manufacturer's datasheet
Is it dead?
Voltage, board powered, black probe on ground.
Working, it reads
Switched on, the output pin sits at the input voltage. Switched off, it sits near 0 V.
Dead, it reads
Output at the input voltage while switched off: the pass element has shorted.
Input present and switched on, no output: failed open, or shut down into a shorted load. Power off and measure output to ground.
On the board:
An output near 0 Ω to ground is usually the load. Lift the output pin to see which.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The pinout and whether the enable is active high or low differ between parts. The datasheet gives both.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AOZ1353LI-04, opens in a new tab
AOZ8310DI-18ESD protection diode, Alpha & Omega SemiconductorESD protection diodeAlpha & Omega Semiconductor
What it is
ESD protection diode
Maker
Alpha & Omega Semiconductor
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AOZ8310DI-18, opens in a new tab
AOZ8809DI-03ESD protection diode, Alpha & Omega SemiconductorESD protection diodeAlpha & Omega Semiconductor
What it is
ESD protection diode
Maker
Alpha & Omega Semiconductor
Package
Not recorded
Pins
Not recorded
Details
ESD protection for high-speed interfaces
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor AOZ8809DI-03, opens in a new tab
BB659C-02VInfineonNot recordedInfineon
What it is
Not recorded
Maker
Infineon
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range and ohms range, part lifted.
Working, it reads
Depends on what it is. The datasheet, or an identical part, says.
Dead, it reads
Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
Open between every pair of pins: failed open, or a part that reads open when working.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BB659C-02V, opens in a new tab
BBY51-03WInfineonNot recordedInfineon
What it is
Not recorded
Maker
Infineon
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range and ohms range, part lifted.
Working, it reads
Depends on what it is. The datasheet, or an identical part, says.
Dead, it reads
Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
Open between every pair of pins: failed open, or a part that reads open when working.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BBY51-03W, opens in a new tab
CESDBLC5V0D7ESD protection diode, JSCJESD protection diodeJSCJ
What it is
ESD protection diode
Maker
JSCJ
Package
Not recorded
Pins
Not recorded
Details
ESD protection diode, VRWM 5 V
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor CESDBLC5V0D7, opens in a new tab
ESD203-B1-02ELESD protection diode, InfineonESD protection diodeInfineon
What it is
ESD protection diode
Maker
Infineon
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor ESD203-B1-02EL, opens in a new tab
ESD203-B1-02ELSESD protection diode, InfineonESD protection diodeInfineon
What it is
ESD protection diode
Maker
Infineon
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor ESD203-B1-02ELS, opens in a new tab
ESDBL5V0AE1ESD protection diode, JSCJESD protection diodeJSCJ
What it is
ESD protection diode
Maker
JSCJ
Package
Not recorded
Pins
Not recorded
Details
ESD protection diode, VRWM 5 V
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor ESDBL5V0AE1, opens in a new tab
IRLML5203P-channel MOSFET, InfineonP-channel MOSFETInfineon
What it is
P-channel MOSFET
Maker
Infineon
Package
Not recorded
Pins
Not recorded
Details
-30V Single P-Channel Power MOSFET in a Micro 3 package
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the drain, black on the source: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor IRLML5203, opens in a new tab
PJSD03TMESD protection diode, PanjitESD protection diodePanjit
What it is
ESD protection diode
Maker
Panjit
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJSD03TM, opens in a new tab
VESD05A1A-HD1ESD protection diode, VishayESD protection diodeVishay
What it is
ESD protection diode
Maker
Vishay
Package
Not recorded
Pins
Not recorded
Details
ESD Protection Diode in LLP1006-2L
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor VESD05A1A-HD1, opens in a new tab

36 more parts have codes that begin with H

Codes that begin with H

For a marking with its end worn or burnt off. Each one shows its full printed code.

BZT52C5V1Hprinted H8SOD-123Zener diode, JSCJZener diodeJSCJ
Printed H8. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
JSCJ
Package
SOD-123
Pins
2
Details
Zener diode, VZ 5.1 V
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BZT52C5V1H, opens in a new tab
MMSZ5241printed H6SOD-123Zener diode, VishayZener diodeVishay
Printed H6. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Vishay
Package
SOD-123
Pins
2
Details
11 V Zener diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMSZ5241, opens in a new tab
MMSZ5241-Gprinted H6SOD-123Zener diode, VishayZener diodeVishay
Printed H6. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Vishay
Package
SOD-123
Pins
2
Details
11 V Zener diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMSZ5241-G, opens in a new tab
MMSZ5241Aprinted H1SOD-123Zener diode, PanjitZener diodePanjit
Printed H1. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Panjit
Package
SOD-123
Pins
2
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMSZ5241A, opens in a new tab
MMSZ5241Bprinted H1SOD-123Zener diode, PanjitZener diodePanjit
Printed H1. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Panjit
Package
SOD-123
Pins
2
Details
SMD Planar Zener Diodes
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMSZ5241B, opens in a new tab
MMSZ5241B-AUprinted H1SOD-123Zener diode, PanjitZener diodePanjit
Printed H1. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Panjit
Package
SOD-123
Pins
2
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMSZ5241B-AU, opens in a new tab
MMSZ5242printed H7SOD-123Zener diode, VishayZener diodeVishay
Printed H7. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Vishay
Package
SOD-123
Pins
2
Details
12 V Zener diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMSZ5242, opens in a new tab
MMSZ5242-Gprinted H7SOD-123Zener diode, VishayZener diodeVishay
Printed H7. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Vishay
Package
SOD-123
Pins
2
Details
12 V Zener diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMSZ5242-G, opens in a new tab
MMSZ5242Aprinted H2SOD-123Zener diode, PanjitZener diodePanjit
Printed H2. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Panjit
Package
SOD-123
Pins
2
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMSZ5242A, opens in a new tab
MMSZ5242Bprinted H2SOD-123Zener diode, PanjitZener diodePanjit
Printed H2. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Panjit
Package
SOD-123
Pins
2
Details
SMD Planar Zener Diodes
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMSZ5242B, opens in a new tab
MMSZ5242B-AUprinted H2SOD-123Zener diode, PanjitZener diodePanjit
Printed H2. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Panjit
Package
SOD-123
Pins
2
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMSZ5242B-AU, opens in a new tab
MMSZ5243printed H8SOD-123Zener diode, VishayZener diodeVishay
Printed H8. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Vishay
Package
SOD-123
Pins
2
Details
13 V Zener diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMSZ5243, opens in a new tab
MMSZ5243-Gprinted H8SOD-123Zener diode, VishayZener diodeVishay
Printed H8. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Vishay
Package
SOD-123
Pins
2
Details
13 V Zener diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMSZ5243-G, opens in a new tab
MMSZ5243Aprinted H3SOD-123Zener diode, PanjitZener diodePanjit
Printed H3. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Panjit
Package
SOD-123
Pins
2
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMSZ5243A, opens in a new tab
MMSZ5243Bprinted H3SOD-123Zener diode, PanjitZener diodePanjit
Printed H3. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Panjit
Package
SOD-123
Pins
2
Details
SMD Planar Zener Diodes
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMSZ5243B, opens in a new tab
MMSZ5243B-AUprinted H3SOD-123Zener diode, PanjitZener diodePanjit
Printed H3. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Panjit
Package
SOD-123
Pins
2
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMSZ5243B-AU, opens in a new tab
MMSZ5244printed H9SOD-123Zener diode, VishayZener diodeVishay
Printed H9. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Vishay
Package
SOD-123
Pins
2
Details
14 V Zener diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMSZ5244, opens in a new tab
MMSZ5244-Gprinted H9SOD-123Zener diode, VishayZener diodeVishay
Printed H9. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Vishay
Package
SOD-123
Pins
2
Details
14 V Zener diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMSZ5244-G, opens in a new tab
MMSZ5244Aprinted H4SOD-123Zener diode, PanjitZener diodePanjit
Printed H4. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Panjit
Package
SOD-123
Pins
2
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMSZ5244A, opens in a new tab
MMSZ5244Bprinted H4SOD-123Zener diode, PanjitZener diodePanjit
Printed H4. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Panjit
Package
SOD-123
Pins
2
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMSZ5244B, opens in a new tab
MMSZ5244B-AUprinted H4SOD-123Zener diode, PanjitZener diodePanjit
Printed H4. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Panjit
Package
SOD-123
Pins
2
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMSZ5244B-AU, opens in a new tab
MMSZ5245printed H0SOD-123Zener diode, VishayZener diodeVishay
Printed H0. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Vishay
Package
SOD-123
Pins
2
Details
15 V Zener diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMSZ5245, opens in a new tab
MMSZ5245-Gprinted H0SOD-123Zener diode, VishayZener diodeVishay
Printed H0. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Vishay
Package
SOD-123
Pins
2
Details
15 V Zener diode
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMSZ5245-G, opens in a new tab
MMSZ5245Aprinted H5SOD-123Zener diode, PanjitZener diodePanjit
Printed H5. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Panjit
Package
SOD-123
Pins
2
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMSZ5245A, opens in a new tab
MMSZ5245Bprinted H5SOD-123Zener diode, PanjitZener diodePanjit
Printed H5. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Panjit
Package
SOD-123
Pins
2
Details
SMD Planar Zener Diodes
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMSZ5245B, opens in a new tab
MMSZ5245B-AUprinted H5SOD-123Zener diode, PanjitZener diodePanjit
Printed H5. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Zener diode
Maker
Panjit
Package
SOD-123
Pins
2
Source
From the manufacturer's datasheet
Is it dead?
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways, forward too: failed open.
Holds well off its rated voltage on the supply test: drifted.
A soft knee, or a voltage that creeps on the supply test: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor MMSZ5245B-AU, opens in a new tab
10 more parts have no package on record. Nothing rules them out, so they stay.
- BB659Cprinted HHInfineonNot recordedInfineon
  Printed HH. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  Not recorded
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range and ohms range, part lifted.
  Working, it reads
  Depends on what it is. The datasheet, or an identical part, says.
  Dead, it reads
  Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
  Open between every pair of pins: failed open, or a part that reads open when working.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BB659C, opens in a new tab
- BB814printed H1InfineonNot recordedInfineon
  Printed H1. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  Not recorded
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range and ohms range, part lifted.
  Working, it reads
  Depends on what it is. The datasheet, or an identical part, says.
  Dead, it reads
  Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
  Open between every pair of pins: failed open, or a part that reads open when working.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BB814, opens in a new tab
- BGH91Bprinted H1RF amplifier (MMIC), InfineonRF amplifier (MMIC)Infineon
  Printed H1. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  RF amplifier (MMIC)
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Voltage, board powered, on the output pin that the bias resistor or choke feeds.
  Working, it reads
  The output pin sits at the device voltage the datasheet gives, a few volts, below the supply.
  Dead, it reads
  Output pin at 0 V, or near 0 Ω to ground with the power off: shorted inside.
  Output pin at the full supply voltage: open inside, no current flowing.
  On the board:
  Measured on the board with power on; the bias network is part of the reading.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  The figures depend on the part and its bias resistor. The datasheet gives both.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BGH91B, opens in a new tab
- BGH92Mprinted H3RF amplifier (MMIC), InfineonRF amplifier (MMIC)Infineon
  Printed H3. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  RF amplifier (MMIC)
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Voltage, board powered, on the output pin that the bias resistor or choke feeds.
  Working, it reads
  The output pin sits at the device voltage the datasheet gives, a few volts, below the supply.
  Dead, it reads
  Output pin at 0 V, or near 0 Ω to ground with the power off: shorted inside.
  Output pin at the full supply voltage: open inside, no current flowing.
  On the board:
  Measured on the board with power on; the bias network is part of the reading.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  The figures depend on the part and its bias resistor. The datasheet gives both.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BGH92M, opens in a new tab
- BGH181Bprinted H2RF amplifier (MMIC), InfineonRF amplifier (MMIC)Infineon
  Printed H2. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  RF amplifier (MMIC)
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Voltage, board powered, on the output pin that the bias resistor or choke feeds.
  Working, it reads
  The output pin sits at the device voltage the datasheet gives, a few volts, below the supply.
  Dead, it reads
  Output pin at 0 V, or near 0 Ω to ground with the power off: shorted inside.
  Output pin at the full supply voltage: open inside, no current flowing.
  On the board:
  Measured on the board with power on; the bias network is part of the reading.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  The figures depend on the part and its bias resistor. The datasheet gives both.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BGH181B, opens in a new tab
- BGH182Mprinted H4RF amplifier (MMIC), InfineonRF amplifier (MMIC)Infineon
  Printed H4. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  RF amplifier (MMIC)
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Voltage, board powered, on the output pin that the bias resistor or choke feeds.
  Working, it reads
  The output pin sits at the device voltage the datasheet gives, a few volts, below the supply.
  Dead, it reads
  Output pin at 0 V, or near 0 Ω to ground with the power off: shorted inside.
  Output pin at the full supply voltage: open inside, no current flowing.
  On the board:
  Measured on the board with power on; the bias network is part of the reading.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  The figures depend on the part and its bias resistor. The datasheet gives both.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BGH182M, opens in a new tab
- BZD27C220Pprinted H3Zener diode, Taiwan SemiconductorZener diodeTaiwan Semiconductor
  Printed H3. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  Zener diode
  Maker
  Taiwan Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
  Working, it reads
  About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  Open both ways, forward too: failed open.
  Holds well off its rated voltage on the supply test: drifted.
  A soft knee, or a voltage that creeps on the supply test: leaky.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BZD27C220P, opens in a new tab
- BZT52C5V1Kprinted H8Zener diode, Taiwan SemiconductorZener diodeTaiwan Semiconductor
  Printed H8. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  Zener diode
  Maker
  Taiwan Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
  Working, it reads
  About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  Open both ways, forward too: failed open.
  Holds well off its rated voltage on the supply test: drifted.
  A soft knee, or a voltage that creeps on the supply test: leaky.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BZT52C5V1K, opens in a new tab
- BZT52C62Kprinted H9Zener diode, Taiwan SemiconductorZener diodeTaiwan Semiconductor
  Printed H9. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  Zener diode
  Maker
  Taiwan Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
  Working, it reads
  About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  Open both ways, forward too: failed open.
  Holds well off its rated voltage on the supply test: drifted.
  A soft knee, or a voltage that creeps on the supply test: leaky.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BZT52C62K, opens in a new tab
- ESDBEH15VA1Sprinted HAESD protection diode, JSCJESD protection diodeJSCJ
  Printed HA. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  ESD protection diode
  Maker
  JSCJ
  Package
  Not recorded
  Pins
  Not recorded
  Details
  ESD protection diode, VRWM 15 V
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, from the protected line to ground, part lifted if you can.
  Working, it reads
  A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
  Dead, it reads
  From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  A reading both ways on a one-way part: leaky.
  A one-way part open both ways: failed open.
  On the board:
  On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
  Compare:
  The same part on the next line or connector pin is the healthy reading to compare with.
  Watch for:
  A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor ESDBEH15VA1S, opens in a new tab

One code, several parts

Marking codes are not unique. In the standard code book, 6H on a SOT-23 is an NPN transistor, a varicap, an N-channel JFET, two digital transistors, a 3.6 V voltage detector: six parts from five makers. So a search shows the parts we hold under that code and under codes easily misread as it, with only the columns that tell them apart.

6Hon a SOT-23, in the code book

NPN transistor
Varicap
N-channel JFET
Digital transistor ×2
3.6 V voltage detector

When more than one is left

Tap Help me choose. Up to 4 quick answers: whether the part has failed, then what separates the parts left. Those get ranked with the reasoning and a test that settles it. That uses one identification: 2 a month are free without an account, and 3 with a free account.

When you cannot read it

Tap the camera in the field. We read the characters, keep the ones we are unsure of, and search every reading. A photo too soft to read is turned back on your phone first; if it is the only one you can get, you can still send it.

What’s printed on it?

14 parts are printed H

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Codes that begin with H

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

One code, several parts

When more than one is left

When you cannot read it