Skip to content

SMD code 1M in SOT-23

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

Not sure which one you have?

Answer up to 4 quick questions and these 39 parts are ranked, with a meter test that settles it. It works on a dead part too.

all SOT-23, 3 pins. What differs:

  • BC848ASOT-23NPN transistor, Taitron ComponentsNPN transistorTaitron Components
    What it is
    NPN transistor
    Maker
    Taitron Components
    Package
    SOT-23
    Pins
    3
    Details
    30 V NPN small-signal transistor, gain group A
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: NPN transistor.

  • BC848BSOT-23NPN transistor, Taitron ComponentsNPN transistorTaitron Components
    What it is
    NPN transistor
    Maker
    Taitron Components
    Package
    SOT-23
    Pins
    3
    Details
    30 V NPN small-signal transistor, gain group B
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: NPN transistor.

  • BC848CSOT-23NPN transistor, Taitron ComponentsNPN transistorTaitron Components
    What it is
    NPN transistor
    Maker
    Taitron Components
    Package
    SOT-23
    Pins
    3
    Details
    30 V NPN small-signal transistor, gain group C
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: NPN transistor.

  • LMBTA13LT1GSOT-23NPN transistor, LRCNPN transistorLRC
    What it is
    NPN transistor
    Maker
    LRC
    Package
    SOT-23
    Pins
    3
    Details
    Bipolar transistor, NPN, IC 300 mA, VCEO 30 V
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: NPN transistor.

  • MMBTA13SOT-23NPN transistor, InfineonNPN transistorInfineon
    What it is
    NPN transistor
    Maker
    Infineon
    Package
    SOT-23
    Pins
    3
    Details
    NPN bipolar transistor
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: NPN transistor.

  • MMBTA13LSOT-23NPN transistor, onsemiNPN transistoronsemi
    What it is
    NPN transistor
    Maker
    onsemi
    Package
    SOT-23
    Pins
    3
    Details
    Darlington Amplifier Transistors
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Darlington transistor.

  • PMBTA13SOT-23NPN transistor, NexperiaNPN transistorNexperia
    What it is
    NPN transistor
    Maker
    Nexperia
    Package
    SOT-23
    Pins
    3
    Details
    30 V, 0.5 A NPN Darlington transistor
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Darlington transistor.

  • S-LMBTA13LT1GSOT-23NPN transistor, LRCNPN transistorLRC
    What it is
    NPN transistor
    Maker
    LRC
    Package
    SOT-23
    Pins
    3
    Details
    Bipolar transistor, NPN, IC 300 mA, VCEO 30 V
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: NPN transistor.

  • SMBTA13SOT-23Transistor, InfineonTransistorInfineon
    What it is
    Transistor
    Maker
    Infineon
    Package
    SOT-23
    Pins
    3
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Bipolar transistor.

  • SMMBTA13LSOT-23NPN transistor, onsemiNPN transistoronsemi
    What it is
    NPN transistor
    Maker
    onsemi
    Package
    SOT-23
    Pins
    3
    Details
    Darlington Amplifier Transistors
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Darlington transistor.

  • BC807-16SOT-23PNP transistor, KECPNP transistorKEC
    What it is
    PNP transistor
    Maker
    KEC
    Package
    SOT-23
    Pins
    3
    Details
    -45 V, -500 mA PNP small-signal transistor, gain group 16
    Source
    Published code list

    Is it dead? The meter test is below: PNP transistor.

  • BC807A-16SOT-23PNP transistor, KECPNP transistorKEC
    What it is
    PNP transistor
    Maker
    KEC
    Package
    SOT-23
    Pins
    3
    Details
    PNP transistor: GP, 50V, 500mA, 350mW, B=100..250, >80MHz
    Source
    Published code list

    Is it dead? The meter test is below: PNP transistor.

  • BC848SOT-23NPN transistor, CdiNPN transistorCdi
    What it is
    NPN transistor
    Maker
    Cdi
    Package
    SOT-23
    Pins
    3
    Details
    NPN bipolar transistor
    Source
    Published code list

    Is it dead? The meter test is below: NPN transistor.

  • FMMT-A13SOT-23Diodes IncorporatedNot recordedDiodes Incorporated
    What it is
    Not recorded
    Maker
    Diodes Incorporated
    Package
    SOT-23
    Pins
    3
    Details
    MPSA13
    Source
    Published code list

    Is it dead? The meter test is below: This part.

  • FMMTA13SOT-23Diodes IncorporatedNot recordedDiodes Incorporated
    What it is
    Not recorded
    Maker
    Diodes Incorporated
    Package
    SOT-23
    Pins
    3
    Details
    Si-npn-Darl: GP, 40V, 300mA, 330mW, B>10000
    Source
    Published code list

    Is it dead? The meter test is below: This part.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

NPN transistor

Diode range, part lifted or its base leg off the pad.

Working, it reads

Red probe on the base reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.

Dead, it reads

  • Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
  • The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
  • Only one junction reads, or none: a junction has failed open. It then looks like a diode.
  • A reading the wrong way round, where it should be open: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Darlington transistor

Diode range, part lifted or its base leg off the pad.

Working, it reads

Red probe on the base reads about 0.6 to 0.75 V to the collector and about 1.1 to 1.4 V to the emitter, two junctions in series, and open the other way round. Collector to emitter reads open. Built-in resistors can change these readings.

Dead, it reads

  • Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
  • The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
  • Only one junction reads, or none: a junction has failed open. It then looks like a diode.
  • A reading the wrong way round, where it should be open: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Bipolar transistor

Diode range, part lifted or its base leg off the pad.

Working, it reads

From the base, one probe colour reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.

Dead, it reads

  • Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
  • The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
  • Only one junction reads, or none: a junction has failed open. It then looks like a diode.
  • A reading the wrong way round, where it should be open: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

PNP transistor

Diode range, part lifted or its base leg off the pad.

Working, it reads

Black probe on the base reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.

Dead, it reads

  • Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
  • The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
  • Only one junction reads, or none: a junction has failed open. It then looks like a diode.
  • A reading the wrong way round, where it should be open: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

This part

Diode range and ohms range, part lifted.

Working, it reads

Depends on what it is. The datasheet, or an identical part, says.

Dead, it reads

  • Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
  • Open between every pair of pins: failed open, or a part that reads open when working.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Printed with a code easy to misread as 1M

One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.

Did you find your part?

Open this in the search to correct a character or try another package.