SMD code 2201
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
2201 on a chip resistor
2.2 kΩ
2.2 kΩ resistor, 1%
220 followed by 1 zero. Four digits is normally the 1% series.
Check it with a meter
Lift one end and measure across it. A good one reads 2.2 kΩ within 1%. Measuring it in circuit reads the parallel combination of everything around it, which is almost always lower, never higher: well above 2.2 kΩ on the board is a fault. Open, or well above 2.2 kΩ, means it has failed: burnt, cracked or corroded. That does not change what to fit: the marking still says 2.2 kΩ. A burnt resistor usually means the part it feeds drew too much, so find that before fitting a new one.
On a transistor or diode body (DFN, SOD-123F), 2201 is a part code instead. Those parts are listed below.
6 parts are printed 2201
Not sure which one you have?
Answer up to 4 quick questions and these 6 parts are ranked, with a meter test that settles it. It works on a dead part too.
JEU3K4DFDFNTVS diode, JieJieTVS diodeDFNNot recordedJieJie
- What it is
- TVS diode
- Maker
- JieJie
- Package
- DFN
- Pins
- Not recorded
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: TVS or ESD protection diode.
WS2.5-4R1NDFNESD protection diode, WayonESD protection diodeDFNNot recordedWayon
- What it is
- ESD protection diode
- Maker
- Wayon
- Package
- DFN
- Pins
- Not recorded
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: TVS or ESD protection diode.
WS3.3-4R1NDFNESD protection diode, WayonESD protection diodeDFNNot recordedWayon
- What it is
- ESD protection diode
- Maker
- Wayon
- Package
- DFN
- Pins
- Not recorded
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: TVS or ESD protection diode.
3 more parts have no package on record
TPS562201DDCDC-DC converter, 6 pins, Texas InstrumentsDC-DC converterNot recorded6 pinsTexas Instruments
- What it is
- DC-DC converter
- Maker
- Texas Instruments
- Package
- Not recorded
- Pins
- 6
- Details
- 4.5V to 17V Input, 2A Synchronous Step-Down Voltage Regulator in SOT-23
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Integrated circuit.
WNMD2201-4N-channel MOSFET, WillsemiN-channel MOSFETNot recordedNot recordedWillsemi
- What it is
- N-channel MOSFET
- Maker
- Willsemi
- Package
- Not recorded
- Pins
- Not recorded
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
AZAD2201BAmazing MicroelectronicNot recordedNot recordedNot recordedAmazing Microelectronic
- What it is
- Not recorded
- Maker
- Amazing Microelectronic
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Linear IC: APA, BTL, class-D, 2.2..5.5V, 2x3.1W(5V/8), shutdown
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
TVS or ESD protection diode
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
- From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
- A reading both ways on a one-way part: leaky.
- A one-way part open both ways: failed open.
- On the board
- , a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
- Compare:
- The same part on the next line or connector pin is the healthy reading to compare with.
- Watch for:
- A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Integrated circuit
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
- A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
- Supply present, output stuck: failed, or its load has.
- On the board:
- A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
- Compare:
- The surest reference is the same IC on a working board, measured pin by pin.
- Watch for:
- Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
N-channel MOSFET
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
- Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
- The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
- No body diode at all: failed open.
- On the board
- the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed with a code easy to misread as 2201
One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.
Codes that begin with 2201
For a marking with its end worn or burnt off. Each code has a page of its own.
Did you find your part?
Open this in the search to correct a character or try another package.