Skip to content

SMD code 24R in SOT-363

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

3 parts in SOT-363 are printed 24R

Not sure which one you have?

Answer up to 4 quick questions and these 6 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • uPA810T-FBSOT-363NEC ElectronicsNEC Electronics
    What it is
    Not recorded
    Maker
    NEC Electronics
    Package
    SOT-363
    Pins
    6
    Details
    NPN transistor: Dual, VHF/UHF, 20V, 100mA, 4.5GHz, B=40..80
    Source
    Published code list

    Is it dead? The meter test is below: Bipolar transistor.

  • µPA810T-FBSOT-363RenesasRenesas
    What it is
    Not recorded
    Maker
    Renesas
    Package
    SOT-363
    Pins
    6
    Details
    Si-npn: Dual, VHF/UHF, 20V, 100mA, 4,5GHz, B=40..80
    Source
    Published code list

    Is it dead? The meter test is below: This part.

  • µPA810TFBSOT-363RenesasRenesas
    What it is
    Not recorded
    Maker
    Renesas
    Package
    SOT-363
    Pins
    6
    Source
    Published code list

    Is it dead? The meter test is below: This part.

  • 3 more parts have no package on record. Nothing rules them out, so they stay.
    • CHSDBDAGP-AChenmkoChenmko
      What it is
      Schottky diode
      Maker
      Chenmko
      Package
      Not recorded
      Pins
      Not recorded
      Details
      SCHOTTKY BARRIER RECTIFIER, 40 V, 2.0 A
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Schottky diode.

    • SMD24AGPChenmkoChenmko
      What it is
      Schottky diode
      Maker
      Chenmko
      Package
      Not recorded
      Pins
      Not recorded
      Details
      SCHOTTKY BARRIER RECTIFIER, 40 V, 2.0 A
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Schottky diode.

    • SMD24APTChenmko EnterpriseChenmko Enterprise
      What it is
      Schottky diode
      Maker
      Chenmko Enterprise
      Package
      Not recorded
      Pins
      Not recorded
      Details
      Diode: SBR, 40V, 2A, Vf<0.5V(2A)
      Source
      Published code list

      Is it dead? The meter test is below: Schottky diode.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

Bipolar transistor

Diode range, part lifted or its base leg off the pad.

Working, it reads

From the base, one probe colour reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.

Dead, it reads

  • Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
  • The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
  • Only one junction reads, or none: a junction has failed open. It then looks like a diode.
  • A reading the wrong way round, where it should be open: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

This part

Diode range and ohms range, part lifted.

Working, it reads

Depends on what it is. The datasheet, or an identical part, says.

Dead, it reads

  • Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
  • Open between every pair of pins: failed open, or a part that reads open when working.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Schottky diode

Diode range, part lifted or one leg off the pad. Red probe on the anode.

Working, it reads

About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • A reading the wrong way round as well: leaky.
  • Open both ways: failed open.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Did you find your part?

Open this in the search to correct a character or try another package.