SMD code 34K
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
34K on a chip resistor
34 kΩ
34 kΩ resistor
The K is both the decimal point and the multiplier: 34 kΩ.
Check it with a meter
Lift one end and measure across it. A good one reads 34 kΩ. Measuring it in circuit reads the parallel combination of everything around it, which is almost always lower, never higher: well above 34 kΩ on the board is a fault. Open, or well above 34 kΩ, means it has failed: burnt, cracked or corroded. That does not change what to fit: the marking still says 34 kΩ. A burnt resistor usually means the part it feeds drew too much, so find that before fitting a new one.
On a transistor or diode body (SOT-523, SOT-23-5, SOT-23), 34K is a part code instead. Those parts are listed below.
39 parts are printed 34K
Not sure which one you have?
Answer up to 4 quick questions and these 39 parts are ranked, with a meter test that settles it. It works on a dead part too.
CJ3134KSOT-23N-channel MOSFET, 3 pins, JSCJN-channel MOSFETSOT-233 pinsJSCJ
- What it is
- N-channel MOSFET
- Maker
- JSCJ
- Package
- SOT-23
- Pins
- 3
- Details
- N-channel MOSFET, 20 V, 1.2 A
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
CJ3134KDWSOT-363Dual N-channel MOSFET, 6 pins, JSCJDual N-channel MOSFETSOT-3636 pinsJSCJ
- What it is
- Dual N-channel MOSFET
- Maker
- JSCJ
- Package
- SOT-363
- Pins
- 6
- Details
- MOSFET, dual N-channel, 20 V, 0.75 A
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET pair.
CMSN3134KDW-HFSOT-363N-channel MOSFET, 6 pins, ComchipN-channel MOSFETSOT-3636 pinsComchip
- What it is
- N-channel MOSFET
- Maker
- Comchip
- Package
- SOT-363
- Pins
- 6
- Details
- 20 V, 0.75 A N-channel MOSFET
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
CMSN3134KT-HFSOT-23N-channel MOSFET, 3 pins, ComchipN-channel MOSFETSOT-233 pinsComchip
- What it is
- N-channel MOSFET
- Maker
- Comchip
- Package
- SOT-23
- Pins
- 3
- Details
- 20 V, 0.75 A N-channel MOSFET
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
DMG1012T-7SOT-523N-channel MOSFET, 3 pins, HXYN-channel MOSFETSOT-5233 pinsHXY
- What it is
- N-channel MOSFET
- Maker
- HXY
- Package
- SOT-523
- Pins
- 3
- Details
- N-channel MOSFET, 20 V, 0.8 A
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
FMFDN3134E-HSOT-363Dual N-channel MOSFET, 6 pins, Formosa MicrosemiDual N-channel MOSFETSOT-3636 pinsFormosa Microsemi
- What it is
- Dual N-channel MOSFET
- Maker
- Formosa Microsemi
- Package
- SOT-363
- Pins
- 6
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET pair.
FMOS3134KTSOT-523MOSFET, 3 pins, Formosa MicrosemiMOSFETSOT-5233 pinsFormosa Microsemi
- What it is
- MOSFET
- Maker
- Formosa Microsemi
- Package
- SOT-523
- Pins
- 3
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: MOSFET.
FMOSVDN3134E-Q1-HSOT-563Dual N-channel MOSFET, 6 pins, Formosa MicrosemiDual N-channel MOSFETSOT-5636 pinsFormosa Microsemi
- What it is
- Dual N-channel MOSFET
- Maker
- Formosa Microsemi
- Package
- SOT-563
- Pins
- 6
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET pair.
FMVN3134E-HSOT-563MOSFET, 6 pins, Formosa MicrosemiMOSFETSOT-5636 pinsFormosa Microsemi
- What it is
- MOSFET
- Maker
- Formosa Microsemi
- Package
- SOT-563
- Pins
- 6
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: MOSFET.
GSFK02002SOT-363Dual N-channel MOSFET, 6 pins, Good-ArkDual N-channel MOSFETSOT-3636 pinsGood-Ark
- What it is
- Dual N-channel MOSFET
- Maker
- Good-Ark
- Package
- SOT-363
- Pins
- 6
- Details
- Dual N-channel MOSFET, 20 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET pair.
HSI3134KEATPSOT-523N-channel MOSFET, 3 pins, HXYN-channel MOSFETSOT-5233 pinsHXY
- What it is
- N-channel MOSFET
- Maker
- HXY
- Package
- SOT-523
- Pins
- 3
- Details
- N-channel MOSFET, 20 V, 0.8 A
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
HSI4153SOT-523N-channel MOSFET, 3 pins, HXYN-channel MOSFETSOT-5233 pinsHXY
- What it is
- N-channel MOSFET
- Maker
- HXY
- Package
- SOT-523
- Pins
- 3
- Details
- N-channel MOSFET, 20 V, 0.8 A
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
HXY1012CISOT-523N-channel MOSFET, 3 pins, HXYN-channel MOSFETSOT-5233 pinsHXY
- What it is
- N-channel MOSFET
- Maker
- HXY
- Package
- SOT-523
- Pins
- 3
- Details
- N-channel MOSFET, 20 V, 0.8 A
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
HXY3134CISOT-523N-channel MOSFET, 3 pins, HXYN-channel MOSFETSOT-5233 pinsHXY
- What it is
- N-channel MOSFET
- Maker
- HXY
- Package
- SOT-523
- Pins
- 3
- Details
- N-channel MOSFET, 20 V, 0.8 A
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
1 more part has no package on record
BRCS3134WBN-channel MOSFET, Blue RocketN-channel MOSFETNot recordedNot recordedBlue Rocket
- What it is
- N-channel MOSFET
- Maker
- Blue Rocket
- Package
- Not recorded
- Pins
- Not recorded
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
N-channel MOSFET
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
- Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
- The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
- No body diode at all: failed open.
- On the board
- the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
N-channel MOSFET pair
Diode range, part lifted. Test drain to source first, then short gate to source and test again. Test each MOSFET on its own pins, as the datasheet's pinout gives them.
Working, it reads
Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
- Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
- The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
- No body diode at all: failed open.
- On the board
- the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
MOSFET
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
- Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
- The gate reads low to source or drain: gate shorted.
- No body diode at all: failed open.
- On the board
- the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Codes that begin with 34K
For a marking with its end worn or burnt off. Each code has a page of its own.
Did you find your part?
Open this in the search to correct a character or try another package.