SMD code 57B
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
57B on a chip resistor
3.83 kΩ
3.83 kΩ resistor, 1%
EIA-96 precision code: 57 stands for 383 in the E96 table, and the letter B is the multiplier, × 10. These are 1% parts.
Check it with a meter
Lift one end and measure across it. A good one reads 3.83 kΩ within 1%. Measuring it in circuit reads the parallel combination of everything around it, which is almost always lower, never higher: well above 3.83 kΩ on the board is a fault. Open, or well above 3.83 kΩ, means it has failed: burnt, cracked or corroded. That does not change what to fit: the marking still says 3.83 kΩ. A burnt resistor usually means the part it feeds drew too much, so find that before fitting a new one.
On a transistor or diode body (SOT-23, SOT-23-5, D2PAK), 57B is a part code instead. Those parts are listed below.
14 parts are printed 57B
Not sure which one you have?
Answer up to 4 quick questions and these 14 parts are ranked, with a meter test that settles it. It works on a dead part too.
BC857BSOT-23PNP transistor, 3 pins, PanjitPNP transistorSOT-233 pinsPanjit
- What it is
- PNP transistor
- Maker
- Panjit
- Package
- SOT-23
- Pins
- 3
- Details
- -50 V PNP small-signal transistor, gain group B
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: PNP transistor.
BC857B-AUSOT-23Transistor, 3 pins, PanjitTransistorSOT-233 pinsPanjit
- What it is
- Transistor
- Maker
- Panjit
- Package
- SOT-23
- Pins
- 3
- Details
- Bipolar transistor
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Bipolar transistor.
BC857BDW-Q1SOT-363Dual PNP transistor, 6 pins, Formosa MicrosemiDual PNP transistorSOT-3636 pinsFormosa Microsemi
- What it is
- Dual PNP transistor
- Maker
- Formosa Microsemi
- Package
- SOT-363
- Pins
- 6
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: PNP transistor pair.
BC857BWSOT-323Transistor, 3 pins, PanjitTransistorSOT-3233 pinsPanjit
- What it is
- Transistor
- Maker
- Panjit
- Package
- SOT-323
- Pins
- 3
- Details
- SMD General Purpose PNP Transistors
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Bipolar transistor.
BC857BW-AUSOT-323Transistor, 3 pins, PanjitTransistorSOT-3233 pinsPanjit
- What it is
- Transistor
- Maker
- Panjit
- Package
- SOT-323
- Pins
- 3
- Details
- Bipolar transistor
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Bipolar transistor.
MMHZ5257BGP-ASOD-123Zener diode, 2 pins, ChenmkoZener diodeSOD-1232 pinsChenmko
- What it is
- Zener diode
- Maker
- Chenmko
- Package
- SOD-123
- Pins
- 2
- Details
- SILICON PLANAR POWER ZENER DIODES, 33 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
MMVZ33VBGP-ASOD-123Zener diode, 2 pins, ChenmkoZener diodeSOD-1232 pinsChenmko
- What it is
- Zener diode
- Maker
- Chenmko
- Package
- SOD-123
- Pins
- 2
- Details
- SILICON PLANAR POWER ZENER DIODES, 33 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
1SMA5957BSMAZener diode, 2 pins, RectronZener diodeSMA2 pinsRectron
- What it is
- Zener diode
- Maker
- Rectron
- Package
- SMA
- Pins
- 2
- Details
- Zener diode: 240V±5%, Zzt=1600, Izm<6mA, 1.5W
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
MMBZ5257BPTSOT-23Zener diode, 3 pins, Chenmko EnterpriseZener diodeSOT-233 pinsChenmko Enterprise
- What it is
- Zener diode
- Maker
- Chenmko Enterprise
- Package
- SOT-23
- Pins
- 3
- Details
- Zener diode: 31.35..34.65V, Izt=5mA, Zzt=88, 225mW
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
MMHZ5257BPTSOD-123Zener diode, 2 pins, Chenmko EnterpriseZener diodeSOD-1232 pinsChenmko Enterprise
- What it is
- Zener diode
- Maker
- Chenmko Enterprise
- Package
- SOD-123
- Pins
- 2
- Details
- Zener diode: 31.35..34.65V, Izt=5mA, Zzt=88, 225mW
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
PSMC5357BSMCZener diode, 2 pins, Plextron TechZener diodeSMC2 pinsPlextron Tech
- What it is
- Zener diode
- Maker
- Plextron Tech
- Package
- SMC
- Pins
- 2
- Details
- Zener diode: 20V±5%, Zzt=3, Ipm=237mA, 5W
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
SMC5357BSMCZener diode, 2 pins, Eris TechnologyZener diodeSMC2 pinsEris Technology
- What it is
- Zener diode
- Maker
- Eris Technology
- Package
- SMC
- Pins
- 2
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
XC6502122MSOT-23LDO regulator, 3 pins, TorexLDO regulatorSOT-233 pinsTorex
- What it is
- LDO regulator
- Maker
- Torex
- Package
- SOT-23
- Pins
- 3
- Details
- Linear voltage regulator IC: LDO, 1.2V±30mV, 200mA
- Source
- Published code list
Is it dead? The meter test is below: Voltage regulator.
XC6502122PSOT-89LDO regulator, 3 pins, TorexLDO regulatorSOT-893 pinsTorex
- What it is
- LDO regulator
- Maker
- Torex
- Package
- SOT-89
- Pins
- 3
- Details
- Linear voltage regulator IC: LDO, 1.2V±30mV, 200mA
- Source
- Published code list
Is it dead? The meter test is below: Voltage regulator.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
PNP transistor
Diode range, part lifted or its base leg off the pad.
Working, it reads
Black probe on the base reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.
Dead, it reads
- Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
- The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
- Only one junction reads, or none: a junction has failed open. It then looks like a diode.
- A reading the wrong way round, where it should be open: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Bipolar transistor
Diode range, part lifted or its base leg off the pad.
Working, it reads
From the base, one probe colour reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.
Dead, it reads
- Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
- The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
- Only one junction reads, or none: a junction has failed open. It then looks like a diode.
- A reading the wrong way round, where it should be open: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
PNP transistor pair
Diode range, part lifted. Test each transistor on its own pins, as the datasheet's pinout gives them.
Working, it reads
Black probe on the base reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.
Dead, it reads
- Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
- The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
- Only one junction reads, or none: a junction has failed open. It then looks like a diode.
- A reading the wrong way round, where it should be open: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Zener diode
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways, forward too: failed open.
- Holds well off its rated voltage on the supply test: drifted.
- A soft knee, or a voltage that creeps on the supply test: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage regulator
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
- Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
- Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
- Power off, input to output near 0 Ω: shorted.
- On the board:
- An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
- Compare:
- The same regulator on another rail or another board shows the right voltages and the right resistances.
- Watch for:
- Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed with a code easy to misread as 57B
One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.
Codes that begin with 57B
For a marking with its end worn or burnt off. Each code has a page of its own.
Did you find your part?
Open this in the search to correct a character or try another package.