Skip to content

SMD code 59B

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

59B on a chip resistor

4.02 kΩ

4.02 kΩ resistor, 1%

EIA-96 precision code: 59 stands for 402 in the E96 table, and the letter B is the multiplier, × 10. These are 1% parts.

Check it with a meter

Lift one end and measure across it. A good one reads 4.02 kΩ within 1%. Measuring it in circuit reads the parallel combination of everything around it, which is almost always lower, never higher: well above 4.02 kΩ on the board is a fault. Open, or well above 4.02 kΩ, means it has failed: burnt, cracked or corroded. That does not change what to fit: the marking still says 4.02 kΩ. A burnt resistor usually means the part it feeds drew too much, so find that before fitting a new one.

On a transistor or diode body (SOT-23, SMC, SOT-89-5), 59B is a part code instead. Those parts are listed below.

7 parts are printed 59B

Not sure which one you have?

Answer up to 4 quick questions and these 7 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • BC859BSOT-23Transistor, 3 pins, PanjitTransistorSOT-233 pinsPanjit
    What it is
    Transistor
    Maker
    Panjit
    Package
    SOT-23
    Pins
    3
    Details
    SMD General Purpose PNP Transistors
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Bipolar transistor.

  • BC859B-AUSOT-23Transistor, 3 pins, PanjitTransistorSOT-233 pinsPanjit
    What it is
    Transistor
    Maker
    Panjit
    Package
    SOT-23
    Pins
    3
    Details
    Bipolar transistor
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Bipolar transistor.

  • BC859BWSOT-323Transistor, 3 pins, PanjitTransistorSOT-3233 pinsPanjit
    What it is
    Transistor
    Maker
    Panjit
    Package
    SOT-323
    Pins
    3
    Details
    SMD General Purpose PNP Transistors
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Bipolar transistor.

  • MMBZ5259BPTSOT-23Zener diode, 3 pins, Chenmko EnterpriseZener diodeSOT-233 pinsChenmko Enterprise
    What it is
    Zener diode
    Maker
    Chenmko Enterprise
    Package
    SOT-23
    Pins
    3
    Details
    Zener diode: 37.05..40.95V, Izt=5mA, Zzt=130, 225mW
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • MMHZ5259BPTSOD-123Zener diode, 2 pins, Chenmko EnterpriseZener diodeSOD-1232 pinsChenmko Enterprise
    What it is
    Zener diode
    Maker
    Chenmko Enterprise
    Package
    SOD-123
    Pins
    2
    Details
    Zener diode: 37.05..40.95V, Izt=5mA, Zzt=130, 225mW
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • PSMC5359BSMCZener diode, 2 pins, Plextron TechZener diodeSMC2 pinsPlextron Tech
    What it is
    Zener diode
    Maker
    Plextron Tech
    Package
    SMC
    Pins
    2
    Details
    Zener diode: 24V±5%, Zzt=4, Ipm=198mA, 5W
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • SMC5359BSMCZener diode, 2 pins, Eris TechnologyZener diodeSMC2 pinsEris Technology
    What it is
    Zener diode
    Maker
    Eris Technology
    Package
    SMC
    Pins
    2
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

Bipolar transistor

Diode range, part lifted or its base leg off the pad.

Working, it reads

From the base, one probe colour reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.

Dead, it reads

  • Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
  • The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
  • Only one junction reads, or none: a junction has failed open. It then looks like a diode.
  • A reading the wrong way round, where it should be open: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Zener diode

Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.

Working, it reads

About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • Open both ways, forward too: failed open.
  • Holds well off its rated voltage on the supply test: drifted.
  • A soft knee, or a voltage that creeps on the supply test: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Printed with a code easy to misread as 59B

One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.

Codes that begin with 59B

For a marking with its end worn or burnt off. Each code has a page of its own.

Codes not listed here are printed on 5 more parts.

Did you find your part?

Open this in the search to correct a character or try another package.