SMD code 8I
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
13 parts are printed 8I
Not sure which one you have?
Answer up to 4 quick questions and these 13 parts are ranked, with a meter test that settles it. It works on a dead part too.
ESD401DPYX1SONESD protection diode, 2 pins, Texas InstrumentsESD protection diodeX1SON2 pinsTexas Instruments
- What it is
- ESD protection diode
- Maker
- Texas Instruments
- Package
- X1SON
- Pins
- 2
- Details
- 1-Channel ESD Protection Diode With Robust IEC ESD Performance
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: TVS or ESD protection diode.
KIA78L15FSOT-89LDO regulator, 3 pins, KECLDO regulatorSOT-893 pinsKEC
- What it is
- LDO regulator
- Maker
- KEC
- Package
- SOT-89
- Pins
- 3
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Voltage regulator.
L78L09CD13TRSOIC-8LDO regulator, 8 pins, STMicroelectronicsLDO regulatorSOIC-88 pinsSTMicroelectronics
- What it is
- LDO regulator
- Maker
- STMicroelectronics
- Package
- SOIC-8
- Pins
- 8
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Voltage regulator.
L78L10ACUTRSOT-89LDO regulator, 3 pins, STMicroelectronicsLDO regulatorSOT-893 pinsSTMicroelectronics
- What it is
- LDO regulator
- Maker
- STMicroelectronics
- Package
- SOT-89
- Pins
- 3
- Details
- LDO regulator, 10 V, 0.1 A
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Voltage regulator.
TPL903215-WS1RWLCSPLDO regulator, 4 pins, 3PEAKLDO regulatorWLCSP4 pins3PEAK
- What it is
- LDO regulator
- Maker
- 3PEAK
- Package
- WLCSP
- Pins
- 4
- Details
- 300-mA High PSRR, Ultra-low Noise LDO
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Voltage regulator.
DTC123TN3SOT-23Digital transistor (NPN, resistors built in), 3 pins, CYStekDigital transistor (NPN, resistors built in)SOT-233 pinsCYStek
- What it is
- Digital transistor (NPN, resistors built in)
- Maker
- CYStek
- Package
- SOT-23
- Pins
- 3
- Details
- NPN digital (resistor-equipped) transistor, R1 2.2K, R2 None
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Digital transistor.
SM6T27CASMBTVS diode, 2 pins, Fagor ElectronicaTVS diodeSMB2 pinsFagor Electronica
- What it is
- TVS diode
- Maker
- Fagor Electronica
- Package
- SMB
- Pins
- 2
- Details
- 600 W TVS diode, bidirectional
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
UN2218SOT-233 pins, PanNot recordedSOT-233 pinsPan
- What it is
- Not recorded
- Maker
- Pan
- Package
- SOT-23
- Pins
- 3
- Details
- Si-npn-Digi: Sw, 50V, 100mA, 200mW, 150MHz, R1/R2=510R/5k1
- Source
- Published code list
Is it dead? The meter test is below: This part.
UN5218SOT-5233 pins, PanasonicNot recordedSOT-5233 pinsPanasonic
- What it is
- Not recorded
- Maker
- Panasonic
- Package
- SOT-523
- Pins
- 3
- Details
- Si-npn-Digi: Sw, 50V, 100mA, 150mW, 150MHz, R1/R2=510R/5k1
- Source
- Published code list
Is it dead? The meter test is below: This part.
UNR2218SOT-233 pins, PanNot recordedSOT-233 pinsPan
- What it is
- Not recorded
- Maker
- Pan
- Package
- SOT-23
- Pins
- 3
- Details
- Si-npn-Digi: Sw, 50V, 100mA, 200mW, 150MHz, R1/R2=510R/5k1
- Source
- Published code list
Is it dead? The meter test is below: This part.
UNR5218SOT-5233 pins, PanasonicNot recordedSOT-5233 pinsPanasonic
- What it is
- Not recorded
- Maker
- Panasonic
- Package
- SOT-523
- Pins
- 3
- Details
- Si-npn-Digi: Sw, 50V, 100mA, 150mW, 150MHz, R1/R2=510R/5k1
- Source
- Published code list
Is it dead? The meter test is below: This part.
2 more parts have no package on record
UN9218JPanNot recordedNot recordedNot recordedPan
- What it is
- Not recorded
- Maker
- Pan
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Si-npn-Digi: Sw, 50V, 100mA, 125mW, 150MHz, R1/R2=510R/5k1
- Source
- Published code list
Is it dead? The meter test is below: This part.
UNR9218JPanNot recordedNot recordedNot recordedPan
- What it is
- Not recorded
- Maker
- Pan
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Si-npn-Digi: Sw, 50V, 100mA, 125mW, 150MHz, R1/R2=510R/5k1
- Source
- Published code list
Is it dead? The meter test is below: This part.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
TVS or ESD protection diode
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
- From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
- A reading both ways on a one-way part: leaky.
- A one-way part open both ways: failed open.
- On the board
- , a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
- Compare:
- The same part on the next line or connector pin is the healthy reading to compare with.
- Watch for:
- A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage regulator
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
- Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
- Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
- Power off, input to output near 0 Ω: shorted.
- On the board:
- An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
- Compare:
- The same regulator on another rail or another board shows the right voltages and the right resistances.
- Watch for:
- Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Digital transistor
Ohms range, part lifted. The datasheet gives the built-in resistors: R1 in series with the base, R2 from base to emitter.
Working, it reads
Base to emitter reads about R1 plus R2 either way round, about 20 kΩ on a 10 k and 10 k part, give or take their wide tolerance. Collector to emitter reads open. A part with no R2 reads a junction behind R1 one way instead.
Dead, it reads
- Collector to emitter the same both ways, near 0 Ω with a continuous beep: shorted.
- From the base, open or far above R1 plus R2: R1 has failed. Static damage shows here most often.
- Base to emitter near 0 Ω: failed short.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- The readings depend on the resistor values, so an identical part elsewhere on the board is the surest reference. Measure it the same way.
- Watch for:
- On the diode range a good part with 10 kΩ resistors reads open on every pair, so a good part looks dead there. Use the ohms range.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
This part
Diode range and ohms range, part lifted.
Working, it reads
Depends on what it is. The datasheet, or an identical part, says.
Dead, it reads
- Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
- Open between every pair of pins: failed open, or a part that reads open when working.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed with a code easy to misread as 8I
One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.
Codes not listed here are printed on 25 more parts.
Did you find your part?
Open this in the search to correct a character or try another package.