SMD code 914A
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
914A on a chip capacitor
910 nF, 10 V
910 nF, 10 V tantalum capacitor
A moulded tantalum capacitor: 914 is the capacitance in picofarads (910 nF) and A is the rated-voltage code (10 V).
Check it with a meter
Lift one end and measure it on a capacitance range. A good one reads close to 910 nF. In circuit the meter also sees everything connected across it, so the reading means little until it is out. It is polarised: the band on the body marks the positive end, and a tantalum fitted backwards fails short, sometimes with a flame. A failed tantalum usually reads near 0 Ω both ways, often with a burnt or cracked body. A failed reading does not change what to fit: the marking still says 910 nF, 10 V. Fit the same capacitance at the same or a higher voltage.
On a transistor or diode body (SMA, SMAF, SOIC-14), 914A is a part code instead. Those parts are listed below.
11 parts are printed 914A
Not sure which one you have?
Answer up to 4 quick questions and these 11 parts are ranked, with a meter test that settles it. It works on a dead part too.
1.5SMA5914ASMAZener diode, 2 pins, Good-ArkZener diodeSMA2 pinsGood-Ark
- What it is
- Zener diode
- Maker
- Good-Ark
- Package
- SMA
- Pins
- 2
- Details
- Zener diode, VZ 3.6 V, 1.5 W
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
1SMA5914-AUSMAZener diode, 2 pins, PanjitZener diodeSMA2 pinsPanjit
- What it is
- Zener diode
- Maker
- Panjit
- Package
- SMA
- Pins
- 2
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
1SMA5914ASMAZener diode, 2 pins, HXYZener diodeSMA2 pinsHXY
- What it is
- Zener diode
- Maker
- HXY
- Package
- SMA
- Pins
- 2
- Details
- Zener diode, 12 V, 0.0312 A
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
PMAZ3V6BSMAZener diode, 2 pins, PrisemiZener diodeSMA2 pinsPrisemi
- What it is
- Zener diode
- Maker
- Prisemi
- Package
- SMA
- Pins
- 2
- Details
- Zener diode, 3.6 V, 1 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
S-SMA5914ASMAZener diode, 2 pins, LeiditechZener diodeSMA2 pinsLeiditech
- What it is
- Zener diode
- Maker
- Leiditech
- Package
- SMA
- Pins
- 2
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
ZGFM5914B-AFSMAFZener diode, 2 pins, Formosa MicrosemiZener diodeSMAF2 pinsFormosa Microsemi
- What it is
- Zener diode
- Maker
- Formosa Microsemi
- Package
- SMAF
- Pins
- 2
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
ZGFM5914B-AF-Q1SMAFZener diode, 2 pins, Formosa MicrosemiZener diodeSMAF2 pinsFormosa Microsemi
- What it is
- Zener diode
- Maker
- Formosa Microsemi
- Package
- SMAF
- Pins
- 2
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
1SMA5914SMAZener diode, 2 pins, PanjitZener diodeSMA2 pinsPanjit
- What it is
- Zener diode
- Maker
- Panjit
- Package
- SMA
- Pins
- 2
- Details
- Zener diode: 3.6V±10%, Zzt=9, Izm<417mA, 1.5W
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
1SMB5914ASMBZener diode, 2 pins, EIC SemiconductorZener diodeSMB2 pinsEIC Semiconductor
- What it is
- Zener diode
- Maker
- EIC Semiconductor
- Package
- SMB
- Pins
- 2
- Details
- Z-diode: 3,6V±10%, Izt=104,2mA, Zzt=9Ω, 3W
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
G9184-080T11USOT-23-5LDO regulator, 5 pins, Global Mixed-mode TechnologyLDO regulatorSOT-23-55 pinsGlobal Mixed-mode Technology
- What it is
- LDO regulator
- Maker
- Global Mixed-mode Technology
- Package
- SOT-23-5
- Pins
- 5
- Details
- Linear voltage regulator IC: LDO, 0.8V±2%, 500mA, +CE
- Source
- Published code list
Is it dead? The meter test is below: Voltage regulator.
Z1.5SMA5914BSMAZener diode, 2 pins, Taitron ComponentsZener diodeSMA2 pinsTaitron Components
- What it is
- Zener diode
- Maker
- Taitron Components
- Package
- SMA
- Pins
- 2
- Details
- Zener diode: 3.42..3.78V, Izt=104.2mA, 1.5W
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
Zener diode
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways, forward too: failed open.
- Holds well off its rated voltage on the supply test: drifted.
- A soft knee, or a voltage that creeps on the supply test: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage regulator
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
- Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
- Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
- Power off, input to output near 0 Ω: shorted.
- On the board:
- An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
- Compare:
- The same regulator on another rail or another board shows the right voltages and the right resistances.
- Watch for:
- Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Codes that begin with 914A
For a marking with its end worn or burnt off. Each code has a page of its own.
Did you find your part?
Open this in the search to correct a character or try another package.