Skip to content

SMD code A00

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

11 parts are printed A00

Not sure which one you have?

Answer up to 4 quick questions and these 11 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • PJA3400SOT-23MOSFET, 3 pins, PanjitMOSFETSOT-233 pinsPanjit
    What it is
    MOSFET
    Maker
    Panjit
    Package
    SOT-23
    Pins
    3
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: MOSFET.

  • SI2300ASOT-23N-channel MOSFET, 3 pins, UMWN-channel MOSFETSOT-233 pinsUMW
    What it is
    N-channel MOSFET
    Maker
    UMW
    Package
    SOT-23
    Pins
    3
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: N-channel MOSFET.

  • SM2300NSASOT-23N-channel MOSFET, 3 pins, Sinopower SemiconductorN-channel MOSFETSOT-233 pinsSinopower Semiconductor
    What it is
    N-channel MOSFET
    Maker
    Sinopower Semiconductor
    Package
    SOT-23
    Pins
    3
    Details
    20 V, 6 A N-channel MOSFET
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: N-channel MOSFET.

  • 74AHC2G00DCMSOP-88 pins, Philips SemiconductorsNot recordedMSOP-88 pinsPhilips Semiconductors
    What it is
    Not recorded
    Maker
    Philips Semiconductors
    Package
    MSOP-8
    Pins
    8
    Details
    CMOS logic IC: Dual 2-input NAND gate
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • 74AHC2G00DPTSSOP-88 pins, Philips SemiconductorsNot recordedTSSOP-88 pinsPhilips Semiconductors
    What it is
    Not recorded
    Maker
    Philips Semiconductors
    Package
    TSSOP-8
    Pins
    8
    Details
    CMOS logic IC: Dual 2-input NAND gate
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • AD8607ARM-R2MSOP-88 pins, Analog DevicesNot recordedMSOP-88 pinsAnalog Devices
    What it is
    Not recorded
    Maker
    Analog Devices
    Package
    MSOP-8
    Pins
    8
    Source
    Published code list

    Is it dead? The meter test is below: This part.

  • HD74ALVC2G00USSSOPRenesasNot recordedSSOPNot recordedRenesas
    What it is
    Not recorded
    Maker
    Renesas
    Package
    SSOP
    Pins
    Not recorded
    Details
    CMOS logic IC: Dual 2-input NAND gate
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • XC6114A131MRSOT-23-5Voltage supervisor, 5 pins, TorexVoltage supervisorSOT-23-55 pinsTorex
    What it is
    Voltage supervisor
    Maker
    Torex
    Package
    SOT-23-5
    Pins
    5
    Details
    CMOS-IC: VDet 3.1V, ±Reset PPO, Wt=6.25ms, Rt=3.13ms
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • 3 more parts have no package on record
    • U74AHC1G00Logic gate, UnisonicLogic gateNot recordedNot recordedUnisonic
      What it is
      Logic gate
      Maker
      Unisonic
      Package
      Not recorded
      Pins
      Not recorded
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Integrated circuit.

    • 74AHC1G00GVNXPNot recordedNot recordedNot recordedNXP
      What it is
      Not recorded
      Maker
      NXP
      Package
      Not recorded
      Pins
      Not recorded
      Details
      AND NO item
      Source
      Published code list

      Is it dead? The meter test is below: This part.

    • 74AHC2G00GDNXPNot recordedNot recordedNot recordedNXP
      What it is
      Not recorded
      Maker
      NXP
      Package
      Not recorded
      Pins
      Not recorded
      Details
      CMOS logic IC: Dual 2-input NAND gate
      Source
      Published code list

      Is it dead? The meter test is below: Integrated circuit.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

MOSFET

Diode range, part lifted. Test drain to source first, then short gate to source and test again.

Working, it reads

One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.

Dead, it reads

  • Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  • The gate reads low to source or drain: gate shorted.
  • No body diode at all: failed open.
On the board
the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

N-channel MOSFET

Diode range, part lifted. Test drain to source first, then short gate to source and test again.

Working, it reads

Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.

Dead, it reads

  • Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  • The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
  • No body diode at all: failed open.
On the board
the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Integrated circuit

Voltage with the board powered; ohms from each pin to ground with it off.

Working, it reads

Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.

Dead, it reads

  • A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  • Supply present, output stuck: failed, or its load has.
On the board:
A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
Compare:
The surest reference is the same IC on a working board, measured pin by pin.
Watch for:
Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

This part

Diode range and ohms range, part lifted.

Working, it reads

Depends on what it is. The datasheet, or an identical part, says.

Dead, it reads

  • Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
  • Open between every pair of pins: failed open, or a part that reads open when working.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Printed with a code easy to misread as A00

One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.

Codes not listed here are printed on 1 more part.

Did you find your part?

Open this in the search to correct a character or try another package.