Skip to content
WhatSMDSign in

SMD code AH in DFN

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

10 parts in DFN are printed AH

Not sure which one you have?

Answer up to 4 quick questions and these 50 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • 7WBD3306MUDFNonsemiNot recordedNot recordedonsemi
    What it is
    Not recorded
    Maker
    onsemi
    Package
    DFN
    Pins
    Not recorded
    Details
    CMOS logic IC: 2-Bit translating bus switch
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • CP2297LDDFNChiphomer TechnologyNot recordedNot recordedChiphomer Technology
    What it is
    Not recorded
    Maker
    Chiphomer Technology
    Package
    DFN
    Pins
    Not recorded
    Details
    Linear IC: APA, BTL, 2.5..5.5V, 3.1W(5V/8), shutdown
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • LD39020ADTPU32RDFN4 pins, STMicroelectronicsNot recorded4 pinsSTMicroelectronics
    What it is
    Not recorded
    Maker
    STMicroelectronics
    Package
    DFN
    Pins
    4
    Details
    equivalent [3.2V LDO]
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

  • NL27WZ02MU2DFNonsemiNot recordedNot recordedonsemi
    What it is
    Not recorded
    Maker
    onsemi
    Package
    DFN
    Pins
    Not recorded
    Details
    CMOS logic IC: Dual 2-input NOR gate
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • NL27WZ08MU1DFNonsemiNot recordedNot recordedonsemi
    What it is
    Not recorded
    Maker
    onsemi
    Package
    DFN
    Pins
    Not recorded
    Details
    CMOS logic IC: Dual 2-input AND gate
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • RP104K251BDFNLDO regulator, RicohLDO regulatorNot recordedRicoh
    What it is
    LDO regulator
    Maker
    Ricoh
    Package
    DFN
    Pins
    Not recorded
    Details
    Linear voltage regulator IC: LDO, 2.5V±0.8%, 150mA, +CE
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

  • RP105K141BDFNLDO regulator, RicohLDO regulatorNot recordedRicoh
    What it is
    LDO regulator
    Maker
    Ricoh
    Package
    DFN
    Pins
    Not recorded
    Details
    Linear voltage regulator IC: LDO, 1.4V±15mV, 400mA, +CE
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

  • RT9012-GSPQVDFNLDO regulator, RichtekLDO regulatorNot recordedRichtek
    What it is
    LDO regulator
    Maker
    Richtek
    Package
    DFN
    Pins
    Not recorded
    Details
    Voltage regulator
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

  • RT9014A-JPPQVDFNLDO regulator, RichtekLDO regulatorNot recordedRichtek
    What it is
    LDO regulator
    Maker
    Richtek
    Package
    DFN
    Pins
    Not recorded
    Details
    Voltage regulator
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

  • WL2815D18-4DFNVoltage supervisor, Will SemiconductorVoltage supervisorNot recordedWill Semiconductor
    What it is
    Voltage supervisor
    Maker
    Will Semiconductor
    Package
    DFN
    Pins
    Not recorded
    Details
    Voltage detector IC: LDO, 1.8V±3%, 150mA, +CE
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • 5 more parts have no package on record. Nothing rules them out, so they stay.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

Integrated circuit

Voltage with the board powered; ohms from each pin to ground with it off.

Working, it reads

Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.

Dead, it reads

  • A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  • Supply present, output stuck: failed, or its load has.
On the board:
A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
Compare:
The surest reference is the same IC on a working board, measured pin by pin.
Watch for:
Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Voltage regulator

Voltage, board powered, black probe on ground. Then ohms with the power off.

Working, it reads

Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.

Dead, it reads

  • Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
  • Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
  • Power off, input to output near 0 Ω: shorted.
On the board:
An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
Compare:
The same regulator on another rail or another board shows the right voltages and the right resistances.
Watch for:
Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Zener diode

Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.

Working, it reads

About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • Open both ways, forward too: failed open.
  • Holds well off its rated voltage on the supply test: drifted.
  • A soft knee, or a voltage that creeps on the supply test: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Printed with a code easy to misread as AH

One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.

Codes that begin with AH

For a marking with its end worn or burnt off. Each code has a page of its own.

Codes not listed here are printed on 162 more parts.

Did you find your part?

Open this in the search to correct a character or try another package.