SMD marking

CACin SOT-23-6

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables.

Not sure which one you have?

Answer up to 4 quick questions and these 6 parts are ranked, with a meter test that settles it. It works on a dead part too.

The only part printed CAC in this package in our tables

TPS3808G125DBV

What it is: Voltage supervisor
Maker: Texas Instruments
Package: SOT-23-6
Pins: 6
Details: Low-Quiescent-Current, Programmable-Delay Supervisory Circuit
Source: From the manufacturer's datasheet

Is it dead?

Voltage with the board powered; ohms from each pin to ground with it off.

Working, it reads

Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.

Dead, it reads

A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
Supply present, output stuck: failed, or its load has.

On the board:: A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
Compare:: The surest reference is the same IC on a working board, measured pin by pin.
Watch for:: Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Datasheet

Printed with a code easy to misread

These parts are printed with a character that is easy to misread as what you typed. The odd one out is marked on each.

TVS diode, all Vishay.

6DFN15Aprinted 6AC
Printed 6AC on the part. Easy to misread as CAC. Check that character with a loupe before you order anything.
What it is
TVS diode
Maker
Vishay
Package
Not recorded
Pins
Not recorded
Details
600 W TVS diode, unidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 6DFN15A, opens in a new tab
6DFN15CAprinted 6AC
Printed 6AC on the part. Easy to misread as CAC. Check that character with a loupe before you order anything.
What it is
TVS diode
Maker
Vishay
Package
Not recorded
Pins
Not recorded
Details
600 W TVS diode, bidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 6DFN15CA, opens in a new tab
6DFN22Aprinted 6AG
Printed 6AG on the part. Easy to misread as CAC. Check that character with a loupe before you order anything.
What it is
TVS diode
Maker
Vishay
Package
Not recorded
Pins
Not recorded
Details
600 W TVS diode, unidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 6DFN22A, opens in a new tab
6DFN22CAprinted 6AG
Printed 6AG on the part. Easy to misread as CAC. Check that character with a loupe before you order anything.
What it is
TVS diode
Maker
Vishay
Package
Not recorded
Pins
Not recorded
Details
600 W TVS diode, bidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor 6DFN22CA, opens in a new tab
SMA6F6.0Aprinted 6AG
Printed 6AG on the part. Easy to misread as CAC. Check that character with a loupe before you order anything.
What it is
TVS diode
Maker
Vishay
Package
Not recorded
Pins
Not recorded
Details
600 W TVS diode, unidirectional
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor SMA6F6.0A, opens in a new tab

6 more parts have codes that begin with CAC

Codes that begin with CAC

For a marking with its end worn or burnt off. Each one shows its full printed code.

Voltage reference. What differs:

ISL21060BFH620Zprinted GACBSOT-23-66 pins, Renesas6 pinsRenesas
Printed GACB. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Voltage reference
Maker
Renesas
Package
SOT-23-6
Pins
6
Source
From the manufacturer's datasheet
Is it dead?
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
Supply present, output stuck: failed, or its load has.
On the board:
A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
Compare:
The surest reference is the same IC on a working board, measured pin by pin.
Watch for:
Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor ISL21060BFH620Z, opens in a new tab
ISL21060BFH641Zprinted GACCSOT-23-66 pins, Renesas6 pinsRenesas
Printed GACC. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Voltage reference
Maker
Renesas
Package
SOT-23-6
Pins
6
Source
From the manufacturer's datasheet
Is it dead?
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
Supply present, output stuck: failed, or its load has.
On the board:
A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
Compare:
The surest reference is the same IC on a working board, measured pin by pin.
Watch for:
Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor ISL21060BFH641Z, opens in a new tab
ISL21060CFH620Zprinted GACDSOT-23-66 pins, Renesas6 pinsRenesas
Printed GACD. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Voltage reference
Maker
Renesas
Package
SOT-23-6
Pins
6
Source
From the manufacturer's datasheet
Is it dead?
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
Supply present, output stuck: failed, or its load has.
On the board:
A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
Compare:
The surest reference is the same IC on a working board, measured pin by pin.
Watch for:
Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor ISL21060CFH620Z, opens in a new tab
ISL21060CFH625Zprinted GAGASOT-23-66 pins, Renesas6 pinsRenesas
Printed GAGA. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Voltage reference
Maker
Renesas
Package
SOT-23-6
Pins
6
Source
From the manufacturer's datasheet
Is it dead?
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
Supply present, output stuck: failed, or its load has.
On the board:
A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
Compare:
The surest reference is the same IC on a working board, measured pin by pin.
Watch for:
Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor ISL21060CFH625Z, opens in a new tab
ISL21060CFH641Zprinted GACESOT-23-66 pins, Renesas6 pinsRenesas
Printed GACE. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Voltage reference
Maker
Renesas
Package
SOT-23-6
Pins
6
Source
From the manufacturer's datasheet
Is it dead?
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
Supply present, output stuck: failed, or its load has.
On the board:
A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
Compare:
The surest reference is the same IC on a working board, measured pin by pin.
Watch for:
Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor ISL21060CFH641Z, opens in a new tab
1 more part has no package on record. Nothing rules them out, so they stay.
- REF2025AIDDCprinted GACM5 pins, Texas Instruments5 pinsTexas Instruments
  Printed GACM. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  Voltage reference
  Maker
  Texas Instruments
  Package
  Not recorded
  Pins
  5
  Details
  Low-Drift, Low-Power, Dual-Output, VREF and VREF / 2 Voltage References
  Source
  From the manufacturer's datasheet
  Is it dead?
  Voltage with the board powered; ohms from each pin to ground with it off.
  Working, it reads
  Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
  Dead, it reads
  A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  Supply present, output stuck: failed, or its load has.
  On the board:
  A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
  Compare:
  The surest reference is the same IC on a working board, measured pin by pin.
  Watch for:
  Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor REF2025AIDDC, opens in a new tab

Open this in the search to correct a character or try another package.