SMD code K5-
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
134 parts are printed K5-
Not sure which one you have?
Answer up to 4 quick questions and these 50 parts are ranked, with a meter test that settles it. It works on a dead part too.
TMMSZ5255ASSOD-323Zener diode, 2 pins, Galaxy MicroelectronicsZener diodeSOD-3232 pinsGalaxy Microelectronics
- What it is
- Zener diode
- Maker
- Galaxy Microelectronics
- Package
- SOD-323
- Pins
- 2
- Details
- 28V, 200mW, Surface Mount Zener Diodes
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
TMMSZ5255BSOD-123Zener diode, 2 pins, Galaxy MicroelectronicsZener diodeSOD-1232 pinsGalaxy Microelectronics
- What it is
- Zener diode
- Maker
- Galaxy Microelectronics
- Package
- SOD-123
- Pins
- 2
- Details
- 28V, 500mW, Surface Mount Zener Diodes
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
TPS3703A7330DSEWSONVoltage supervisor, 6 pins, Texas InstrumentsVoltage supervisorWSON6 pinsTexas Instruments
- What it is
- Voltage supervisor
- Maker
- Texas Instruments
- Package
- WSON
- Pins
- 6
- Details
- High Accuracy Overvoltage and Undervoltage Reset IC With Time Delay and Manual Reset
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Integrated circuit.
TSV991AIQ1TDFNOperational amplifier, STMicroelectronicsOperational amplifierDFNNot recordedSTMicroelectronics
- What it is
- Operational amplifier
- Maker
- STMicroelectronics
- Package
- DFN
- Pins
- Not recorded
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Integrated circuit.
ZD5255AS2SOD-323Zener diode, 2 pins, CYStekZener diodeSOD-3232 pinsCYStek
- What it is
- Zener diode
- Maker
- CYStek
- Package
- SOD-323
- Pins
- 2
- Details
- 28 V zener diode
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
ZD5255ASHSOD-123Zener diode, 2 pins, CYStekZener diodeSOD-1232 pinsCYStek
- What it is
- Zener diode
- Maker
- CYStek
- Package
- SOD-123
- Pins
- 2
- Details
- 28 V zener diode
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
ZD5255BS2SOD-323Zener diode, 2 pins, CYStekZener diodeSOD-3232 pinsCYStek
- What it is
- Zener diode
- Maker
- CYStek
- Package
- SOD-323
- Pins
- 2
- Details
- 28 V zener diode
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
ZD5255BSHSOD-123Zener diode, 2 pins, CYStekZener diodeSOD-1232 pinsCYStek
- What it is
- Zener diode
- Maker
- CYStek
- Package
- SOD-123
- Pins
- 2
- Details
- 28 V zener diode
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
2SC3143-5SOT-233 pins, Sanyo ElectricNot recordedSOT-233 pinsSanyo Electric
- What it is
- Not recorded
- Maker
- Sanyo Electric
- Package
- SOT-23
- Pins
- 3
- Details
- Si-npn: AF-Drv, 180V, 80mA, 200mW, 150MHz, B=135..270
- Source
- Published code list
Is it dead? The meter test is below: This part.
2SK160-5SOT-233 pins, NEC ElectronicsNot recordedSOT-233 pinsNEC Electronics
- What it is
- Not recorded
- Maker
- NEC Electronics
- Package
- SOT-23
- Pins
- 3
- Details
- FET n-type: VHF, 30V, 20mA, 150mW, Idss=1..3mA, Up<4.5V
- Source
- Published code list
Is it dead? The meter test is below: MOSFET.
2SK160K5SOT-233 pinsNot recordedSOT-233 pinsNot recorded
- What it is
- Not recorded
- Maker
- Not recorded
- Package
- SOT-23
- Pins
- 3
- Source
- Published code list
Is it dead? The meter test is below: This part.
2SK853-5SOT-3233 pins, NEC ElectronicsNot recordedSOT-3233 pinsNEC Electronics
- What it is
- Not recorded
- Maker
- NEC Electronics
- Package
- SOT-323
- Pins
- 3
- Details
- FET n-type: GP, 30V, 10mA, 150mW, Idss=2..5mA, Up<4.5V
- Source
- Published code list
Is it dead? The meter test is below: MOSFET.
3 more parts have no package on record
74AVCH1T45GMNXPNot recordedNot recordedNot recordedNXP
- What it is
- Not recorded
- Maker
- NXP
- Package
- Not recorded
- Pins
- Not recorded
- Details
- CMOS logic IC: Dual supply translating transceiver with 3-state output
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
74AVCH1T45GNNXPNot recordedNot recordedNot recordedNXP
- What it is
- Not recorded
- Maker
- NXP
- Package
- Not recorded
- Pins
- Not recorded
- Details
- CMOS logic IC: Dual supply translating transceiver with 3-state output
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
74AVCH1T45GSNXPNot recordedNot recordedNot recordedNXP
- What it is
- Not recorded
- Maker
- NXP
- Package
- Not recorded
- Pins
- Not recorded
- Details
- CMOS logic IC: Dual supply translating transceiver with 3-state output
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
Zener diode
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways, forward too: failed open.
- Holds well off its rated voltage on the supply test: drifted.
- A soft knee, or a voltage that creeps on the supply test: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Integrated circuit
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
- A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
- Supply present, output stuck: failed, or its load has.
- On the board:
- A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
- Compare:
- The surest reference is the same IC on a working board, measured pin by pin.
- Watch for:
- Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
This part
Diode range and ohms range, part lifted.
Working, it reads
Depends on what it is. The datasheet, or an identical part, says.
Dead, it reads
- Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
- Open between every pair of pins: failed open, or a part that reads open when working.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
MOSFET
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
- Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
- The gate reads low to source or drain: gate shorted.
- No body diode at all: failed open.
- On the board
- the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Did you find your part?
Open this in the search to correct a character or try another package.