SMD code L-
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
136 parts are printed L-
Not sure which one you have?
Answer up to 4 quick questions and these 50 parts are ranked, with a meter test that settles it. It works on a dead part too.
NLU1G14AMUDFNonsemiNot recordedDFNNot recordedonsemi
- What it is
- Not recorded
- Maker
- onsemi
- Package
- DFN
- Pins
- Not recorded
- Details
- CMOS logic IC: Inverter with Schmitt-trigger input
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
NLU1GT32CMUDFNonsemiNot recordedDFNNot recordedonsemi
- What it is
- Not recorded
- Maker
- onsemi
- Package
- DFN
- Pins
- Not recorded
- Details
- CMOS logic IC: 2-input OR gate with voltage-level translator
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
NLU1GT50MUDFNonsemiNot recordedDFNNot recordedonsemi
- What it is
- Not recorded
- Maker
- onsemi
- Package
- DFN
- Pins
- Not recorded
- Details
- CMOS logic IC: Noninverting buffer, TTL level
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
NLU1GT50MUTCGDFN6 pins, onsemiNot recordedDFN6 pinsonsemi
- What it is
- Not recorded
- Maker
- onsemi
- Package
- DFN
- Pins
- 6
- Source
- Published code list
Is it dead? The meter test is below: This part.
NLU1GT86MUDFNonsemiNot recordedDFNNot recordedonsemi
- What it is
- Not recorded
- Maker
- onsemi
- Package
- DFN
- Pins
- Not recorded
- Details
- CMOS logic IC: 2-input EXCLUSIVE-OR gate, TTL level
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
NLU1GT125CMUDFNonsemiNot recordedDFNNot recordedonsemi
- What it is
- Not recorded
- Maker
- onsemi
- Package
- DFN
- Pins
- Not recorded
- Details
- CMOS logic IC: Bus buffer gate with 3-state output, TTL level
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
NLX2G04MUDFNonsemiNot recordedDFNNot recordedonsemi
- What it is
- Not recorded
- Maker
- onsemi
- Package
- DFN
- Pins
- Not recorded
- Details
- CMOS logic IC: Dual inverter
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
NSBA113EF3TSOT-1123Digital transistor (PNP, resistors built in), 3 pins, onsemiDigital transistor (PNP, resistors built in)SOT-11233 pinsonsemi
- What it is
- Digital transistor (PNP, resistors built in)
- Maker
- onsemi
- Package
- SOT-1123
- Pins
- 3
- Details
- PNP transistor: Sw, 50V, 100mA, 200mW, R1/R2=1k/1k
- Source
- Published code list
Is it dead? The meter test is below: Digital transistor.
NSBA114TF3TSOT-1123PNP transistor, 3 pins, onsemiPNP transistorSOT-11233 pinsonsemi
- What it is
- PNP transistor
- Maker
- onsemi
- Package
- SOT-1123
- Pins
- 3
- Details
- PNP transistor: Sw, 50V, 100mA, 200mW, R=10k
- Source
- Published code list
Is it dead? The meter test is below: PNP transistor.
NZ9F6V8STSOD-923Zener diode, 2 pins, onsemiZener diodeSOD-9232 pinsonsemi
- What it is
- Zener diode
- Maker
- onsemi
- Package
- SOD-923
- Pins
- 2
- Details
- Zener diode: 6.65..6.93V, Izt=5mA, Zzt=40, 200mW
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
NZ9F12VTSOD-923Zener diode, 2 pins, onsemiZener diodeSOD-9232 pinsonsemi
- What it is
- Zener diode
- Maker
- onsemi
- Package
- SOD-923
- Pins
- 2
- Details
- Zener diode: 11.40..12.60V, Izt=5mA, Zzt=30, 200mW
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
4 more parts have no package on record
NLU1GT50AMXonsemiNot recordedNot recordedNot recordedonsemi
- What it is
- Not recorded
- Maker
- onsemi
- Package
- Not recorded
- Pins
- Not recorded
- Details
- CMOS logic IC: Noninverting buffer, TTL level
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
NLU1GT50CMXonsemiNot recordedNot recordedNot recordedonsemi
- What it is
- Not recorded
- Maker
- onsemi
- Package
- Not recorded
- Pins
- Not recorded
- Details
- CMOS logic IC: Noninverting buffer, TTL level
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
PMCA14UN3 pins, Nexperia B.V.Not recordedNot recorded3 pinsNexperia B.V.
- What it is
- Not recorded
- Maker
- Nexperia B.V.
- Package
- Not recorded
- Pins
- 3
- Source
- Published code list
Is it dead? The meter test is below: This part.
SB02W03CSchottky diode, Sanyo ElectricSchottky diodeNot recordedNot recordedSanyo Electric
- What it is
- Schottky diode
- Maker
- Sanyo Electric
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Diode: Dual, SBR, HF, 30V, 200mA, Vf<0.55V(200mA), 6.3pF, 10ns
- Source
- Published code list
Is it dead? The meter test is below: Schottky diode.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
Integrated circuit
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
- A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
- Supply present, output stuck: failed, or its load has.
- On the board:
- A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
- Compare:
- The surest reference is the same IC on a working board, measured pin by pin.
- Watch for:
- Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
This part
Diode range and ohms range, part lifted.
Working, it reads
Depends on what it is. The datasheet, or an identical part, says.
Dead, it reads
- Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
- Open between every pair of pins: failed open, or a part that reads open when working.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Digital transistor
Ohms range, part lifted. The datasheet gives the built-in resistors: R1 in series with the base, R2 from base to emitter.
Working, it reads
Base to emitter reads about R1 plus R2 either way round, about 20 kΩ on a 10 k and 10 k part, give or take their wide tolerance. Collector to emitter reads open. A part with no R2 reads a junction behind R1 one way instead.
Dead, it reads
- Collector to emitter the same both ways, near 0 Ω with a continuous beep: shorted.
- From the base, open or far above R1 plus R2: R1 has failed. Static damage shows here most often.
- Base to emitter near 0 Ω: failed short.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- The readings depend on the resistor values, so an identical part elsewhere on the board is the surest reference. Measure it the same way.
- Watch for:
- On the diode range a good part with 10 kΩ resistors reads open on every pair, so a good part looks dead there. Use the ohms range.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
PNP transistor
Diode range, part lifted or its base leg off the pad.
Working, it reads
Black probe on the base reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.
Dead, it reads
- Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
- The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
- Only one junction reads, or none: a junction has failed open. It then looks like a diode.
- A reading the wrong way round, where it should be open: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Zener diode
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways, forward too: failed open.
- Holds well off its rated voltage on the supply test: drifted.
- A soft knee, or a voltage that creeps on the supply test: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Schottky diode
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- A reading the wrong way round as well: leaky.
- Open both ways: failed open.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Did you find your part?
Open this in the search to correct a character or try another package.