SMD marking

L15

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables.

Not sure which one you have?

Answer up to 4 quick questions and these 2 parts are ranked, with a meter test that settles it. It works on a dead part too.

The only part printed L15 in our tables

ESDBL15VA1

What it is: ESD protection diode
Maker: JSCJ
Package: Not recorded
Pins: Not recorded
Details: ESD protection diode, VRWM 15 V
Source: From the manufacturer's datasheet

Is it dead?

Diode range, from the protected line to ground, part lifted if you can.

Working, it reads

A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.

Dead, it reads

From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.

On the board:: On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:: The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:: A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Datasheet

Printed with a code easy to misread

This part is printed with a character that is easy to misread as what you typed. The odd one out is marked on each.

SS0115TWprinted 115SOT-363Schottky diode, 6 pins, PanjitSchottky diodeSOT-3636 pinsPanjit
Printed 115 on the part. Easy to misread as L15. Check that character with a loupe before you order anything.
What it is
Schottky diode
Maker
Panjit
Package
SOT-363
Pins
6
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
A reading the wrong way round as well: leaky.
Open both ways: failed open.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor SS0115TW, opens in a new tab

4 more parts have codes that begin with L15

Codes that begin with L15

For a marking with its end worn or burnt off. Each one shows its full printed code.

SS115FSHprinted 115FSHSOD-128Schottky diode, 2 pins, Taiwan SemiconductorSchottky diodeSOD-1282 pinsTaiwan Semiconductor
Printed 115FSH. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Schottky diode
Maker
Taiwan Semiconductor
Package
SOD-128
Pins
2
Details
Rectifier schottky
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
A reading the wrong way round as well: leaky.
Open both ways: failed open.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor SS115FSH, opens in a new tab
TPS709A33DBVprinted 11SFSOT-23-5LDO regulator, 5 pins, Texas InstrumentsLDO regulatorSOT-23-55 pinsTexas Instruments
Printed 11SF. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
LDO regulator
Maker
Texas Instruments
Package
SOT-23-5
Pins
5
Details
150-mA, 30-V, 1-µA IQ Voltage Regulators With Enable
Source
From the manufacturer's datasheet
Is it dead?
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
Power off, input to output near 0 Ω: shorted.
On the board:
An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
Compare:
The same regulator on another rail or another board shows the right voltages and the right resistances.
Watch for:
Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor TPS709A33DBV, opens in a new tab
2 more parts have no package on record
- SS115ALHprinted 115ALHSchottky diode, Taiwan SemiconductorSchottky diodeNot recordedNot recordedTaiwan Semiconductor
  Printed 115ALH. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  Schottky diode
  Maker
  Taiwan Semiconductor
  Package
  Not recorded
  Pins
  Not recorded
  Details
  Rectifier schottky
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range, part lifted or one leg off the pad. Red probe on the anode.
  Working, it reads
  About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
  Dead, it reads
  The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  A reading the wrong way round as well: leaky.
  Open both ways: failed open.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  Watch for:
  A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor SS115ALH, opens in a new tab
- TLV6700DDCprinted 1I51Voltage supervisor, 6 pins, Texas InstrumentsVoltage supervisorNot recorded6 pinsTexas Instruments
  Printed 1I51. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
  What it is
  Voltage supervisor
  Maker
  Texas Instruments
  Package
  Not recorded
  Pins
  6
  Details
  Micropower, 18-V Window Comparator With 400-mV Reference
  Source
  From the manufacturer's datasheet
  Is it dead?
  Voltage with the board powered; ohms from each pin to ground with it off.
  Working, it reads
  Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
  Dead, it reads
  A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  Supply present, output stuck: failed, or its load has.
  On the board:
  A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
  Compare:
  The surest reference is the same IC on a working board, measured pin by pin.
  Watch for:
  Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor TLV6700DDC, opens in a new tab

Open this in the search to correct a character or try another package.