SMD marking

LM1in SOT-363

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables.

Not sure which one you have?

Answer up to 4 quick questions and these 3 parts are ranked, with a meter test that settles it. It works on a dead part too.

The only part printed LM1 in this package in our tables

BCM847BS

What it is: Transistor
Maker: Diotec
Package: SOT-363
Pins: 6
Details: SMD Matched NPN Transistors
Source: From the manufacturer's datasheet

Is it dead?

Diode range, part lifted or its base leg off the pad.

Working, it reads

From the base, one probe colour reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.

Dead, it reads

Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
Only one junction reads, or none: a junction has failed open. It then looks like a diode.
A reading the wrong way round, where it should be open: leaky.

On the board:: On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:: If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:: A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Datasheet

Printed with a code easy to misread

These parts are printed with a character that is easy to misread as what you typed. The odd one out is marked on each.

Rectifier, all Taiwan Semiconductor.

S1MLprinted 1ML
Printed 1ML on the part. Easy to misread as LM1. Check that character with a loupe before you order anything.
What it is
Rectifier
Maker
Taiwan Semiconductor
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways: failed open.
A reading the wrong way round as well: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor S1ML, opens in a new tab
S1MLHprinted 1ML
Printed 1ML on the part. Easy to misread as LM1. Check that character with a loupe before you order anything.
What it is
Rectifier
Maker
Taiwan Semiconductor
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways: failed open.
A reading the wrong way round as well: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor S1MLH, opens in a new tab

2 more parts have codes that begin with LM1

Codes that begin with LM1

For a marking with its end worn or burnt off. Each one shows its full printed code.

Rectifier, all Taiwan Semiconductor.

S1MLSprinted 1MLS
Printed 1MLS. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Rectifier
Maker
Taiwan Semiconductor
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways: failed open.
A reading the wrong way round as well: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor S1MLS, opens in a new tab
S1MLSHprinted 1MLS
Printed 1MLS. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Rectifier
Maker
Taiwan Semiconductor
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
Open both ways: failed open.
A reading the wrong way round as well: leaky.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor S1MLSH, opens in a new tab

Open this in the search to correct a character or try another package.