SMD code MA6 in SOT-23
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
10 parts in SOT-23 are printed MA6
Not sure which one you have?
Answer up to 4 quick questions and these 10 parts are ranked, with a meter test that settles it. It works on a dead part too.
all SOT-23, 3 pins. What differs:
5N10-HXYSOT-23N-channel MOSFET, HXYN-channel MOSFETHXY
- What it is
- N-channel MOSFET
- Maker
- HXY
- Package
- SOT-23
- Pins
- 3
- Details
- N-channel MOSFET, 100 V, 5 A
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
AP10TN135NSOT-23N-channel MOSFET, HXYN-channel MOSFETHXY
- What it is
- N-channel MOSFET
- Maker
- HXY
- Package
- SOT-23
- Pins
- 3
- Details
- 100 V, 2.1 A N-channel MOSFET
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
HI7208SOT-23N-channel MOSFET, HXYN-channel MOSFETHXY
- What it is
- N-channel MOSFET
- Maker
- HXY
- Package
- SOT-23
- Pins
- 3
- Details
- N-channel MOSFET, 100 V, 5 A
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
HXY5N10AISOT-23N-channel MOSFET, HXYN-channel MOSFETHXY
- What it is
- N-channel MOSFET
- Maker
- HXY
- Package
- SOT-23
- Pins
- 3
- Details
- N-channel MOSFET, 100 V, 5 A
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
LMBD2838LT1GSOT-23Switching diode, LRCSwitching diodeLRC
- What it is
- Switching diode
- Maker
- LRC
- Package
- SOT-23
- Pins
- 3
- Details
- Switching diode, VR 50 V, IF 100 mA, VF Max 1 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
LMTL5N10SOT-23N-channel MOSFET, LeiditechN-channel MOSFETLeiditech
- What it is
- N-channel MOSFET
- Maker
- Leiditech
- Package
- SOT-23
- Pins
- 3
- Details
- N-channel MOSFET, 100 V, 5 A
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
MMBD2838LSOT-23Switching diode, onsemiSwitching diodeonsemi
- What it is
- Switching diode
- Maker
- onsemi
- Package
- SOT-23
- Pins
- 3
- Details
- Monolithic Dual Switching Diodes
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
S-LMBD2838LT1GSOT-23Switching diode, LRCSwitching diodeLRC
- What it is
- Switching diode
- Maker
- LRC
- Package
- SOT-23
- Pins
- 3
- Details
- Switching diode, VR 50 V, IF 100 mA, VF Max 1 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
MMBD2838SOT-23onsemiNot recordedonsemi
- What it is
- Not recorded
- Maker
- onsemi
- Package
- SOT-23
- Pins
- 3
- Details
- Si-diode: Dual, Sw, 50V, 150mA, 225mW, Vf>1,2V(100mA), <4ns
- Source
- Published code list
Is it dead? The meter test is below: Silicon diode.
MMBD2838LT1SOT-23onsemiNot recordedonsemi
- What it is
- Not recorded
- Maker
- onsemi
- Package
- SOT-23
- Pins
- 3
- Source
- Published code list
Is it dead? The meter test is below: This part.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
N-channel MOSFET
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
- Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
- The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
- No body diode at all: failed open.
- On the board
- the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Silicon diode
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways: failed open.
- A reading the wrong way round as well: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
This part
Diode range and ohms range, part lifted.
Working, it reads
Depends on what it is. The datasheet, or an identical part, says.
Dead, it reads
- Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
- Open between every pair of pins: failed open, or a part that reads open when working.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed with a code easy to misread as MA6
One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.
Did you find your part?
Open this in the search to correct a character or try another package.