SMD code P86
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
P86 on a chip capacitor
0.86 pF
0.86 pF capacitor
The p is both the decimal point and the unit: 0.86 pF.
Check it with a meter
Lift one end and measure it on a capacitance range. A good one reads close to 0.86 pF. In circuit the meter also sees everything connected across it, so the reading means little until it is out. A failed one usually reads near 0 Ω, or a steady low resistance, on the ohms range, often from a crack. On the board a shorted capacitor shorts its whole rail. A failed reading does not change what to fit: the marking still says 0.86 pF.
On a transistor or diode body (SOT-23-5, SOT-23, SOT-89), P86 is a part code instead. Those parts are listed below.
16 parts are printed P86
Not sure which one you have?
Answer up to 4 quick questions and these 16 parts are ranked, with a meter test that settles it. It works on a dead part too.
2SB1386GPSOT-89PNP transistor, 3 pins, ChenmkoPNP transistorSOT-893 pinsChenmko
- What it is
- PNP transistor
- Maker
- Chenmko
- Package
- SOT-89
- Pins
- 3
- Details
- PNP Epitaxial Transistor, 20 V, 5 A
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: PNP transistor.
NC7SP86P5SOT-23-5Logic gate, 5 pins, onsemiLogic gateSOT-23-55 pinsonsemi
- What it is
- Logic gate
- Maker
- onsemi
- Package
- SOT-23-5
- Pins
- 5
- Details
- TinyLogic ULP-A Exclusive-OR Gate
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Integrated circuit.
2SB1386PT-PSOT-89PNP transistor, 3 pins, Chenmko EnterprisePNP transistorSOT-893 pinsChenmko Enterprise
- What it is
- PNP transistor
- Maker
- Chenmko Enterprise
- Package
- SOT-89
- Pins
- 3
- Details
- PNP transistor: AF, Sw, 20V, 5A, B=82..180, 120MHz
- Source
- Published code list
Is it dead? The meter test is below: PNP transistor.
BZX84-A75SOT-23Zener diode, 3 pins, NXPZener diodeSOT-233 pinsNXP
- What it is
- Zener diode
- Maker
- NXP
- Package
- SOT-23
- Pins
- 3
- Details
- 75 V ±1% voltage regulator (Zener) diode
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
LN61FN4842MSOT-23Voltage supervisor, 3 pins, Shanghai Natlinear ElectronicsVoltage supervisorSOT-233 pinsShanghai Natlinear Electronics
- What it is
- Voltage supervisor
- Maker
- Shanghai Natlinear Electronics
- Package
- SOT-23
- Pins
- 3
- Details
- Voltage detector IC: 4.8V±2%, +Reset ODO, Rdt=400ms
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
LN61FN4842PSOT-89Voltage supervisor, 3 pins, Shanghai Natlinear ElectronicsVoltage supervisorSOT-893 pinsShanghai Natlinear Electronics
- What it is
- Voltage supervisor
- Maker
- Shanghai Natlinear Electronics
- Package
- SOT-89
- Pins
- 3
- Details
- Voltage detector IC: 4.8V±2%, +Reset ODO, 400ms Rt delay
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
NC7SP86PSOT-3535 pins, Fairchild SemiconductorNot recordedSOT-3535 pinsFairchild Semiconductor
- What it is
- Not recorded
- Maker
- Fairchild Semiconductor
- Package
- SOT-353
- Pins
- 5
- Details
- CMOS logic IC: 2-input EXCLUSIVE-OR gate
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
U74AUP1G86G-AE5SOT-23-55 pins, UnisonicNot recordedSOT-23-55 pinsUnisonic
- What it is
- Not recorded
- Maker
- Unisonic
- Package
- SOT-23-5
- Pins
- 5
- Details
- CMOS logic IC: 2-input EXCLUSIVE-OR gate, H-free
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
U74AUP1G86G-AL5SOT-3535 pins, UnisonicNot recordedSOT-3535 pinsUnisonic
- What it is
- Not recorded
- Maker
- Unisonic
- Package
- SOT-353
- Pins
- 5
- Details
- CMOS logic IC: 2-input EXCLUSIVE-OR gate, H-free
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
XC61FN4842MSOT-23Voltage supervisor, 3 pins, TorexVoltage supervisorSOT-233 pinsTorex
- What it is
- Voltage supervisor
- Maker
- Torex
- Package
- SOT-23
- Pins
- 3
- Details
- CMOS-IC: Voltage Detector 4,8V, Reset Open drain output, 400ms
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
XC61FN4842PSOT-89Voltage supervisor, 3 pins, TorexVoltage supervisorSOT-893 pinsTorex
- What it is
- Voltage supervisor
- Maker
- Torex
- Package
- SOT-89
- Pins
- 3
- Details
- CMOS-IC: Voltage Detector 4,8V, Reset Open drain output, 400ms
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
4 more parts have no package on record
74AUP2G86DCNXPNot recordedNot recordedNot recordedNXP
- What it is
- Not recorded
- Maker
- NXP
- Package
- Not recorded
- Pins
- Not recorded
- Details
- CMOS logic IC: Dual 2-input EXCLUSIVE-OR gate
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
74AUP2G86GDNXPNot recordedNot recordedNot recordedNXP
- What it is
- Not recorded
- Maker
- NXP
- Package
- Not recorded
- Pins
- Not recorded
- Details
- CMOS logic IC: Dual 2-input EXCLUSIVE-OR gate
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
74AUP2G86GMNXPNot recordedNot recordedNot recordedNXP
- What it is
- Not recorded
- Maker
- NXP
- Package
- Not recorded
- Pins
- Not recorded
- Details
- CMOS logic IC: Dual 2-input EXCLUSIVE-OR gate
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
74AUP2G86GTNXPNot recordedNot recordedNot recordedNXP
- What it is
- Not recorded
- Maker
- NXP
- Package
- Not recorded
- Pins
- Not recorded
- Details
- CMOS logic IC: Dual 2-input EXCLUSIVE-OR gate
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
PNP transistor
Diode range, part lifted or its base leg off the pad.
Working, it reads
Black probe on the base reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.
Dead, it reads
- Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
- The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
- Only one junction reads, or none: a junction has failed open. It then looks like a diode.
- A reading the wrong way round, where it should be open: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Integrated circuit
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
- A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
- Supply present, output stuck: failed, or its load has.
- On the board:
- A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
- Compare:
- The surest reference is the same IC on a working board, measured pin by pin.
- Watch for:
- Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Zener diode
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways, forward too: failed open.
- Holds well off its rated voltage on the supply test: drifted.
- A soft knee, or a voltage that creeps on the supply test: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed with a code easy to misread as P86
One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.
Codes that begin with P86
For a marking with its end worn or burnt off. Each code has a page of its own.
Did you find your part?
Open this in the search to correct a character or try another package.