Skip to content
WhatSMDSign in

SMD code R6D

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables.

3 parts are printed R6D

Not sure which one you have?

Answer up to 4 quick questions and these 3 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • LM4040QDIM3-2.5SOT-23Voltage reference, 3 pins, Texas Instruments
    What it is
    Voltage reference
    Maker
    Texas Instruments
    Package
    SOT-23
    Pins
    3
    Details
    LM4040-N/-Q1 Precision Micropower Shunt Voltage Reference
    Source
    From the manufacturer's datasheet

    Is it dead? The meter test is below: Integrated circuit.

    Datasheetfor LM4040QDIM3-2.5, opens in a new tab
  • LM4040QDIM3X2.5SOT-23Voltage reference, 3 pins, Texas Instruments
    What it is
    Voltage reference
    Maker
    Texas Instruments
    Package
    SOT-23
    Pins
    3
    Details
    LM4040-N/-Q1 Precision Micropower Shunt Voltage Reference
    Source
    From the manufacturer's datasheet

    Is it dead? The meter test is below: Integrated circuit.

    Datasheetfor LM4040QDIM3X2.5, opens in a new tab
  • RS1006D1SOD-123Rectifier, 2 pins, JSCJ
    What it is
    Rectifier
    Maker
    JSCJ
    Package
    SOD-123
    Pins
    2
    Details
    Rectifier, 600 V, 1 A
    Source
    From the manufacturer's datasheet

    Is it dead? The meter test is below: Silicon diode.

    Datasheetfor RS1006D1, opens in a new tab

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

Integrated circuit

Voltage with the board powered; ohms from each pin to ground with it off.

Working, it reads

Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.

Dead, it reads

  • A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  • Supply present, output stuck: failed, or its load has.
On the board:
A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
Compare:
The surest reference is the same IC on a working board, measured pin by pin.
Watch for:
Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Silicon diode

Diode range, part lifted or one leg off the pad. Red probe on the anode.

Working, it reads

About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • Open both ways: failed open.
  • A reading the wrong way round as well: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Codes that begin with R6D

For a marking with its end worn or burnt off. Each code has a page of its own.

Open this in the search to correct a character or try another package.