Skip to content

SMD code S3

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

Not sure which one you have?

Answer up to 4 quick questions and these 50 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • SFM13SOD-323Rectifier, 2 pins, RectronRectifierSOD-3232 pinsRectron
    What it is
    Rectifier
    Maker
    Rectron
    Package
    SOD-323
    Pins
    2
    Details
    Rectifier diode
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Silicon diode.

  • SFM13-MSOD-123Rectifier, 2 pins, Formosa MicrosemiRectifierSOD-1232 pinsFormosa Microsemi
    What it is
    Rectifier
    Maker
    Formosa Microsemi
    Package
    SOD-123
    Pins
    2
    Details
    Rectifier diode
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Silicon diode.

  • SMS2303-CSOT-23MOSFET, 3 pins, SeCoSMOSFETSOT-233 pinsSeCoS
    What it is
    MOSFET
    Maker
    SeCoS
    Package
    SOT-23
    Pins
    3
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: MOSFET.

  • SMS3922-079LFSOD-523Schottky diode, 2 pins, SkyworksSchottky diodeSOD-5232 pinsSkyworks
    What it is
    Schottky diode
    Maker
    Skyworks
    Package
    SOD-523
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Schottky diode.

  • SS13SMASchottky diode, 2 pins, Taitron ComponentsSchottky diodeSMA2 pinsTaitron Components
    What it is
    Schottky diode
    Maker
    Taitron Components
    Package
    SMA
    Pins
    2
    Details
    Surface Mount Schottky Rectifiers
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Schottky diode.

  • SS23SMBSchottky diode, 2 pins, Taitron ComponentsSchottky diodeSMB2 pinsTaitron Components
    What it is
    Schottky diode
    Maker
    Taitron Components
    Package
    SMB
    Pins
    2
    Details
    Surface Mount Schottky Rectifiers
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Schottky diode.

  • SS33SMCSchottky diode, 2 pins, Taitron ComponentsSchottky diodeSMC2 pinsTaitron Components
    What it is
    Schottky diode
    Maker
    Taitron Components
    Package
    SMC
    Pins
    2
    Details
    Surface Mount Schottky Rectifiers
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Schottky diode.

  • 8 more parts have no package on record
    • SFM13-MHRectifier, Formosa MicrosemiRectifierNot recordedNot recordedFormosa Microsemi
      What it is
      Rectifier
      Maker
      Formosa Microsemi
      Package
      Not recorded
      Pins
      Not recorded
      Details
      Rectifier diode
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Silicon diode.

    • SFM13-MSRectifier, Formosa MicrosemiRectifierNot recordedNot recordedFormosa Microsemi
      What it is
      Rectifier
      Maker
      Formosa Microsemi
      Package
      Not recorded
      Pins
      Not recorded
      Details
      Rectifier diode
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Silicon diode.

    • SFM13-MS-Q1Rectifier, Formosa MicrosemiRectifierNot recordedNot recordedFormosa Microsemi
      What it is
      Rectifier
      Maker
      Formosa Microsemi
      Package
      Not recorded
      Pins
      Not recorded
      Details
      Rectifier diode
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Silicon diode.

    • SGM894B-1.6XXEJ4GVoltage supervisor, 4 pins, SG MicroVoltage supervisorNot recorded4 pinsSG Micro
      What it is
      Voltage supervisor
      Maker
      SG Micro
      Package
      Not recorded
      Pins
      4
      Details
      Voltage Detector with Delay Time Adjustable
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Integrated circuit.

    • SS13BSchottky diode, Taitron ComponentsSchottky diodeNot recordedNot recordedTaitron Components
      What it is
      Schottky diode
      Maker
      Taitron Components
      Package
      Not recorded
      Pins
      Not recorded
      Details
      Surface Mount Schottky Rectifiers
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Schottky diode.

    • TPS22914BYFPLoad switch, 4 pins, Texas InstrumentsLoad switchNot recorded4 pinsTexas Instruments
      What it is
      Load switch
      Maker
      Texas Instruments
      Package
      Not recorded
      Pins
      4
      Details
      5.5V, 2A, 37mΩ On-Resistance Load Switch
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Load switch.

    • TSD035-101WSSchottky diode, Taitron ComponentsSchottky diodeNot recordedNot recordedTaitron Components
      What it is
      Schottky diode
      Maker
      Taitron Components
      Package
      Not recorded
      Pins
      Not recorded
      Details
      Schottky Barrier Diodes (Two Terminals)
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Schottky diode.

    • ULC0342P26LVESD protection diode, LeiditechESD protection diodeNot recordedNot recordedLeiditech
      What it is
      ESD protection diode
      Maker
      Leiditech
      Package
      Not recorded
      Pins
      Not recorded
      Details
      ESD protection diode, VRWM 3.3 V, Cj 1.5 pF
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: TVS or ESD protection diode.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

Silicon diode

Diode range, part lifted or one leg off the pad. Red probe on the anode.

Working, it reads

About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • Open both ways: failed open.
  • A reading the wrong way round as well: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Integrated circuit

Voltage with the board powered; ohms from each pin to ground with it off.

Working, it reads

Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.

Dead, it reads

  • A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  • Supply present, output stuck: failed, or its load has.
On the board:
A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
Compare:
The surest reference is the same IC on a working board, measured pin by pin.
Watch for:
Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

MOSFET

Diode range, part lifted. Test drain to source first, then short gate to source and test again.

Working, it reads

One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.

Dead, it reads

  • Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  • The gate reads low to source or drain: gate shorted.
  • No body diode at all: failed open.
On the board
the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Schottky diode

Diode range, part lifted or one leg off the pad. Red probe on the anode.

Working, it reads

About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • A reading the wrong way round as well: leaky.
  • Open both ways: failed open.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Load switch

Voltage, board powered, black probe on ground.

Working, it reads

Switched on, the output pin sits at the input voltage. Switched off, it sits near 0 V.

Dead, it reads

  • Output at the input voltage while switched off: the pass element has shorted.
  • Input present and switched on, no output: failed open, or shut down into a shorted load. Power off and measure output to ground.
On the board:
An output near 0 Ω to ground is usually the load. Lift the output pin to see which.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The pinout and whether the enable is active high or low differ between parts. The datasheet gives both.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

TVS or ESD protection diode

Diode range, from the protected line to ground, part lifted if you can.

Working, it reads

A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.

Dead, it reads

  • From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  • A reading both ways on a one-way part: leaky.
  • A one-way part open both ways: failed open.
On the board
, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Did you find your part?

Open this in the search to correct a character or try another package.