SMD code TS2
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
14 parts are printed TS2
Not sure which one you have?
Answer up to 4 quick questions and these 14 parts are ranked, with a meter test that settles it. It works on a dead part too.
ACE7402ASOT-323N-channel MOSFET, 3 pins, HXYN-channel MOSFETSOT-3233 pinsHXY
- What it is
- N-channel MOSFET
- Maker
- HXY
- Package
- SOT-323
- Pins
- 3
- Details
- N-channel MOSFET, 20 V, 2 A
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
AP1334GEUSOT-323N-channel MOSFET, 3 pins, HXYN-channel MOSFETSOT-3233 pinsHXY
- What it is
- N-channel MOSFET
- Maker
- HXY
- Package
- SOT-323
- Pins
- 3
- Details
- N-channel MOSFET, 20 V, 2 A
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
GSFKW0202SOT-323N-channel MOSFET, 3 pins, Good-ArkN-channel MOSFETSOT-3233 pinsGood-Ark
- What it is
- N-channel MOSFET
- Maker
- Good-Ark
- Package
- SOT-323
- Pins
- 3
- Details
- N-channel MOSFET, 20 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
HSI2102ASOT-323N-channel MOSFET, 3 pins, HXYN-channel MOSFETSOT-3233 pinsHXY
- What it is
- N-channel MOSFET
- Maker
- HXY
- Package
- SOT-323
- Pins
- 3
- Details
- N-channel MOSFET, 20 V, 2 A
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
HXY2102EISOT-323N-channel MOSFET, 3 pins, HXYN-channel MOSFETSOT-3233 pinsHXY
- What it is
- N-channel MOSFET
- Maker
- HXY
- Package
- SOT-323
- Pins
- 3
- Details
- N-channel MOSFET, 20 V, 2 A
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
SI2102ASOT-323N-channel MOSFET, 3 pins, HXYN-channel MOSFETSOT-3233 pinsHXY
- What it is
- N-channel MOSFET
- Maker
- HXY
- Package
- SOT-323
- Pins
- 3
- Details
- N-channel MOSFET, 20 V, 2 A
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
SSF2102-CSOT-323MOSFET, 3 pins, SeCoSMOSFETSOT-3233 pinsSeCoS
- What it is
- MOSFET
- Maker
- SeCoS
- Package
- SOT-323
- Pins
- 3
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: MOSFET.
SSF2102Y-CSOT-323MOSFET, 3 pins, SeCoSMOSFETSOT-3233 pinsSeCoS
- What it is
- MOSFET
- Maker
- SeCoS
- Package
- SOT-323
- Pins
- 3
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: MOSFET.
WM02N20GSOT-3233 pins, WayonNot recordedSOT-3233 pinsWayon
- What it is
- Not recorded
- Maker
- Wayon
- Package
- SOT-323
- Pins
- 3
- Details
- MOSFET
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: MOSFET.
BZX84-B3V3SOT-23Zener diode, 3 pins, NXPZener diodeSOT-233 pinsNXP
- What it is
- Zener diode
- Maker
- NXP
- Package
- SOT-23
- Pins
- 3
- Details
- 3.3 V ±2% voltage regulator (Zener) diode
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
BZX84-B3V6SOT-23Zener diode, 3 pins, NexperiaZener diodeSOT-233 pinsNexperia
- What it is
- Zener diode
- Maker
- Nexperia
- Package
- SOT-23
- Pins
- 3
- Details
- 3.6 V ±2% voltage regulator (Zener) diode
- Source
- An older or alternative marking, from a published code list
Is it dead? The meter test is below: Zener diode.
3 more parts have no package on record
LM2102WN-channel MOSFET, LeiditechN-channel MOSFETNot recordedNot recordedLeiditech
- What it is
- N-channel MOSFET
- Maker
- Leiditech
- Package
- Not recorded
- Pins
- Not recorded
- Details
- N-channel MOSFET, 20 V, 2.5 A
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
NTS0102TLLogic level translator, 8 pins, NXPLogic level translatorNot recorded8 pinsNXP
- What it is
- Logic level translator
- Maker
- NXP
- Package
- Not recorded
- Pins
- 8
- Details
- 1 General description 2 Features and benefits 3 Applications 4 Ordering information
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Integrated circuit.
NTS0102TL-Q100Logic level translator, 8 pins, NXPLogic level translatorNot recorded8 pinsNXP
- What it is
- Logic level translator
- Maker
- NXP
- Package
- Not recorded
- Pins
- 8
- Details
- 1 General description 2 Features and benefits 3 Applications
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Integrated circuit.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
N-channel MOSFET
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
- Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
- The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
- No body diode at all: failed open.
- On the board
- the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Integrated circuit
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
- A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
- Supply present, output stuck: failed, or its load has.
- On the board:
- A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
- Compare:
- The surest reference is the same IC on a working board, measured pin by pin.
- Watch for:
- Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
MOSFET
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
- Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
- The gate reads low to source or drain: gate shorted.
- No body diode at all: failed open.
- On the board
- the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Zener diode
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways, forward too: failed open.
- Holds well off its rated voltage on the supply test: drifted.
- A soft knee, or a voltage that creeps on the supply test: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed with a code easy to misread as TS2
One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.
Codes that begin with TS2
For a marking with its end worn or burnt off. Each code has a page of its own.
Codes not listed here are printed on 74 more parts.
Did you find your part?
Open this in the search to correct a character or try another package.