1.2 kΩ resistor. 30 parts are printed 122. 73 printed with a similar-looking code.
122 on a chip resistor
1.2 kΩ resistor, 5%
12 followed by 2 zeros. Three digits is normally the 5% series. The same marking also reads as 1.2 nF on a capacitor or 1.2 mH on an inductor, and nothing in the code says which; the body of the part does.
Lift one end and measure across it. A good one reads 1.2 kΩ within 5%. Measuring it in circuit reads the parallel combination of everything around it, which is almost always lower, never higher: well above 1.2 kΩ on the board is a fault. Open, or well above 1.2 kΩ, means it has failed: burnt, cracked or corroded. That does not change what to fit: the marking still says 1.2 kΩ. A burnt resistor usually means the part it feeds drew too much, so find that before fitting a new one.
On a transistor or diode body (SOT-23, SOT-23-5, SOT-223), 122 is a part code instead. Those parts are listed below.
Not sure which one you have?
Answer up to 4 quick questions and these 30 parts are ranked, with a meter test that settles it. It works on a dead part too.
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
One character differs, and it is one that is easy to confuse under a lamp. The odd one out is marked on each.
Printed L22 on the part. Easy to misread as 122. Check that character with a loupe before you order anything.
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed 12Z on the part. Easy to misread as 122. Check that character with a loupe before you order anything.
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed 12Z on the part. Easy to misread as 122. Check that character with a loupe before you order anything.
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed L22 on the part. Easy to misread as 122. Check that character with a loupe before you order anything.
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed L22 on the part. Easy to misread as 122. Check that character with a loupe before you order anything.
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed L22 on the part. Easy to misread as 122. Check that character with a loupe before you order anything.
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed L22 on the part. Easy to misread as 122. Check that character with a loupe before you order anything.
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed L22 on the part. Easy to misread as 122. Check that character with a loupe before you order anything.
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed 12Z on the part. Easy to misread as 122. Check that character with a loupe before you order anything.
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed 12Z on the part. Easy to misread as 122. Check that character with a loupe before you order anything.
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed L22 on the part. Easy to misread as 122. Check that character with a loupe before you order anything.
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed L22 on the part. Easy to misread as 122. Check that character with a loupe before you order anything.
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed 12Z on the part. Easy to misread as 122. Check that character with a loupe before you order anything.
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed 12Z on the part. Easy to misread as 122. Check that character with a loupe before you order anything.
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed IZ2 on the part. Easy to misread as 122. Check that character with a loupe before you order anything.
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed L22 on the part. Easy to misread as 122. Check that character with a loupe before you order anything.
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed L22 on the part. Easy to misread as 122. Check that character with a loupe before you order anything.
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed L22 on the part. Easy to misread as 122. Check that character with a loupe before you order anything.
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed L22 on the part. Easy to misread as 122. Check that character with a loupe before you order anything.
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed L22 on the part. Easy to misread as 122. Check that character with a loupe before you order anything.
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
53 more parts are not listed here. Type more of the code to narrow the list.