SMD code -1D in SOT-323
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
10 parts in SOT-323 are printed -1D
Not sure which one you have?
Answer up to 4 quick questions and these 33 parts are ranked, with a meter test that settles it. It works on a dead part too.
BAV199FMSOT-323Switching diode, 3 pins, ROHMSwitching diode3 pinsROHM
- What it is
- Switching diode
- Maker
- ROHM
- Package
- SOT-323
- Pins
- 3
- Details
- Switching Diode (Low leakage)
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
BAV199FMFHSOT-323Switching diode, 3 pins, ROHMSwitching diode3 pinsROHM
- What it is
- Switching diode
- Maker
- ROHM
- Package
- SOT-323
- Pins
- 3
- Details
- Switching Diode (Low leakage) (AEC-Q101 qualified)
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
BC846WSOT-323NPN transistor, 3 pins, NexperiaNPN transistor3 pinsNexperia
- What it is
- NPN transistor
- Maker
- Nexperia
- Package
- SOT-323
- Pins
- 3
- Pinout
- 1 base
- 2 emitter
- 3 collector
- Details
- NPN bipolar transistor
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: NPN transistor.
FMBTA42WSOT-323NPN transistor, 3 pins, Formosa MicrosemiNPN transistor3 pinsFormosa Microsemi
- What it is
- NPN transistor
- Maker
- Formosa Microsemi
- Package
- SOT-323
- Pins
- 3
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: NPN transistor.
FMBTA42W-Q1SOT-323NPN transistor, 3 pins, Formosa MicrosemiNPN transistor3 pinsFormosa Microsemi
- What it is
- NPN transistor
- Maker
- Formosa Microsemi
- Package
- SOT-323
- Pins
- 3
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: NPN transistor.
L2SC4083PWT1GSOT-323NPN transistor, 3 pins, LRCNPN transistor3 pinsLRC
- What it is
- NPN transistor
- Maker
- LRC
- Package
- SOT-323
- Pins
- 3
- Details
- Bipolar transistor, NPN, IC 50 mA, VCEO 11 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: NPN transistor.
S-L2SC4083PWT1GSOT-323NPN transistor, 3 pins, LRCNPN transistor3 pinsLRC
- What it is
- NPN transistor
- Maker
- LRC
- Package
- SOT-323
- Pins
- 3
- Details
- Bipolar transistor, NPN, IC 50 mA, VCEO 11 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: NPN transistor.
2SC4083SOT-323NPN transistor, 3 pins, ROHMNPN transistor3 pinsROHM
- What it is
- NPN transistor
- Maker
- ROHM
- Package
- SOT-323
- Pins
- 3
- Details
- NPN bipolar transistor
- Source
- Published code list
Is it dead? The meter test is below: NPN transistor.
BC846BWSOT-323Transistor, 3 pins, NXPTransistor3 pinsNXP
- What it is
- Transistor
- Maker
- NXP
- Package
- SOT-323
- Pins
- 3
- Details
- SMD General Purpose NPN Transistors
- Source
- Published code list
Is it dead? The meter test is below: Bipolar transistor.
BC846USOT-3233 pins, InfineonNot recorded3 pinsInfineon
- What it is
- Not recorded
- Maker
- Infineon
- Package
- SOT-323
- Pins
- 3
- Details
- Si-npn: Dual, AF, 80V, 100mA, 250mW, B=110..450, >100MHz
- Source
- Published code list
Is it dead? The meter test is below: This part.
5 more parts have no package on record. Nothing rules them out, so they stay.
AS1DHS-HFRectifier, ComchipRectifierNot recordedComchip
- What it is
- Rectifier
- Maker
- Comchip
- Package
- Not recorded
- Pins
- Not recorded
- Details
- 200 V, 1 A rectifier
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Silicon diode.
EMB32N03VATN-channel MOSFET, Excelliance MOSN-channel MOSFETNot recordedExcelliance MOS
- What it is
- N-channel MOSFET
- Maker
- Excelliance MOS
- Package
- Not recorded
- Pins
- Not recorded
- Details
- 30 V, 5.5 A N-channel MOSFET
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: N-channel MOSFET.
MM5Z56V-Q1Zener diode, Formosa MicrosemiZener diodeNot recordedFormosa Microsemi
- What it is
- Zener diode
- Maker
- Formosa Microsemi
- Package
- Not recorded
- Pins
- Not recorded
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
SS10200HESchottky diode, Galaxy MicroelectronicsSchottky diodeNot recordedGalaxy Microelectronics
- What it is
- Schottky diode
- Maker
- Galaxy Microelectronics
- Package
- Not recorded
- Pins
- Not recorded
- Details
- 1A, 200V, Surface Mount Schottky Barrier Rectifiers
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Schottky diode.
BD46E462G-MVoltage supervisor, ROHMVoltage supervisorNot recordedROHM
- What it is
- Voltage supervisor
- Maker
- ROHM
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Voltage detector IC: 4.6V±1%, -MR, -Reset PPO, Rdt=200ms
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
Silicon diode
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways: failed open.
- A reading the wrong way round as well: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
NPN transistor
Diode range, part lifted or its base leg off the pad.
Working, it reads
Red probe on the base reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.
Dead, it reads
- Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
- The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
- Only one junction reads, or none: a junction has failed open. It then looks like a diode.
- A reading the wrong way round, where it should be open: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Bipolar transistor
Diode range, part lifted or its base leg off the pad.
Working, it reads
From the base, one probe colour reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.
Dead, it reads
- Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
- The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
- Only one junction reads, or none: a junction has failed open. It then looks like a diode.
- A reading the wrong way round, where it should be open: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
This part
Diode range and ohms range, part lifted.
Working, it reads
Depends on what it is. The datasheet, or an identical part, says.
Dead, it reads
- Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
- Open between every pair of pins: failed open, or a part that reads open when working.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
N-channel MOSFET
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
- Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
- The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
- No body diode at all: failed open.
- On the board
- the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Zener diode
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways, forward too: failed open.
- Holds well off its rated voltage on the supply test: drifted.
- A soft knee, or a voltage that creeps on the supply test: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Schottky diode
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- A reading the wrong way round as well: leaky.
- Open both ways: failed open.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Integrated circuit
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
- A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
- Supply present, output stuck: failed, or its load has.
- On the board:
- A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
- Compare:
- The surest reference is the same IC on a working board, measured pin by pin.
- Watch for:
- Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed with a code easy to misread as -1D
One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.
Codes not listed here are printed on 35 more parts.
Did you find your part?
Open this in the search to correct a character or try another package.