SMD code 00 in SOD-323
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
00 on a chip resistor
0 Ω
Zero-ohm link
A zero-ohm link: a jumper in a resistor body, used to bridge a track or select an option. It is not a failed part.
Check it with a meter
Measure across it on the lowest ohms range: a link reads under an ohm. If it reads open, the link itself has failed, which does happen when it has been used as a fuse. Then something after it drew too much: find that before bridging it again.
On a transistor or diode body (SOT-23-6, SOT-23-5, SMC), 00 is a part code instead. Those parts are listed below.
12 parts in SOD-323 are printed 00
Not sure which one you have?
Answer up to 4 quick questions and these 30 parts are ranked, with a meter test that settles it. It works on a dead part too.
BZT52C2V4SSOD-323Zener diode, Formosa MicrosemiZener diodeFormosa Microsemi
- What it is
- Zener diode
- Maker
- Formosa Microsemi
- Package
- SOD-323
- Pins
- 2
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
BZT52C2V4S-Q1SOD-323Zener diode, Formosa MicrosemiZener diodeFormosa Microsemi
- What it is
- Zener diode
- Maker
- Formosa Microsemi
- Package
- SOD-323
- Pins
- 2
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
LM3Z2V4PT1GSOD-323Zener diode, LRCZener diodeLRC
- What it is
- Zener diode
- Maker
- LRC
- Package
- SOD-323
- Pins
- 2
- Details
- Zener diode, VZ Min 2.2 V, VZ Nom 2.4 V, VZ Max 2.6 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
LM3Z2V4T1GSOD-323Zener diode, LeiditechZener diodeLeiditech
- What it is
- Zener diode
- Maker
- Leiditech
- Package
- SOD-323
- Pins
- 2
- Details
- Zener diode, VZ Min 2.2 V, VZ Nom 2.4 V, VZ Max 2.6 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
MM3Z2V4SOD-323Zener diode, LeiditechZener diodeLeiditech
- What it is
- Zener diode
- Maker
- Leiditech
- Package
- SOD-323
- Pins
- 2
- Details
- SMD Planar Zener Diodes
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
MMPZ5221BGP-ASOD-323Zener diode, ChenmkoZener diodeChenmko
- What it is
- Zener diode
- Maker
- Chenmko
- Package
- SOD-323
- Pins
- 2
- Details
- SILICON PLANAR POWER ZENER DIODES, 2.4 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
S-LM3Z2V4PT1GSOD-323Zener diode, LRCZener diodeLRC
- What it is
- Zener diode
- Maker
- LRC
- Package
- SOD-323
- Pins
- 2
- Details
- Zener diode, VZ Min 2.2 V, VZ Nom 2.4 V, VZ Max 2.6 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
BZX384C2V4SOD-323Zener diode, Taitron ComponentsZener diodeTaitron Components
- What it is
- Zener diode
- Maker
- Taitron Components
- Package
- SOD-323
- Pins
- 2
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
FDZ2.4T1GSOD-323Zener diode, First SilionZener diodeFirst Silion
- What it is
- Zener diode
- Maker
- First Silion
- Package
- SOD-323
- Pins
- 2
- Details
- Zener diode: 2.2..2.6V, Izt=5mA, Zzt=100, 200mW
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
MM3Z2V4T1SOD-323MotorolaNot recordedMotorola
- What it is
- Not recorded
- Maker
- Motorola
- Package
- SOD-323
- Pins
- 2
- Details
- Стабилитрон (Zener)
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
MMPZ5221BPTSOD-323Zener diode, Chenmko EnterpriseZener diodeChenmko Enterprise
- What it is
- Zener diode
- Maker
- Chenmko Enterprise
- Package
- SOD-323
- Pins
- 2
- Details
- Zener diode: 2.280..2.520V, Izt=5mA, Zzt=100, 225mW
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
ZD02V4SOD-323Cystech ElectronicsNot recordedCystech Electronics
- What it is
- Not recorded
- Maker
- Cystech Electronics
- Package
- SOD-323
- Pins
- 2
- Details
- Z-diode: 2.2..2.6V, 5mA, Zzt=100Ω, 200mW
- Source
- Published code list
Is it dead? The meter test is below: Silicon diode.
3 more parts have no package on record. Nothing rules them out, so they stay.
MM5Z2V4-Q1Zener diode, Formosa MicrosemiZener diodeFormosa Microsemi
- What it is
- Zener diode
- Maker
- Formosa Microsemi
- Package
- Not recorded
- Pins
- Not recorded
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Zener diode.
AP8822C-40GIVoltage supervisor, Anwell SemiconductorVoltage supervisorAnwell Semiconductor
- What it is
- Voltage supervisor
- Maker
- Anwell Semiconductor
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Voltage detector IC: 4.0V±2%, -Reset PPO, 200ms Rt delay, H-free
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
AP8822C-40GSVoltage supervisor, Anwell SemiconductorVoltage supervisorAnwell Semiconductor
- What it is
- Voltage supervisor
- Maker
- Anwell Semiconductor
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Voltage detector IC: 4.0V±2%, -Reset PPO, 200ms Rt delay, H-free
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
Zener diode
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways, forward too: failed open.
- Holds well off its rated voltage on the supply test: drifted.
- A soft knee, or a voltage that creeps on the supply test: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Silicon diode
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways: failed open.
- A reading the wrong way round as well: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Integrated circuit
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
- A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
- Supply present, output stuck: failed, or its load has.
- On the board:
- A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
- Compare:
- The surest reference is the same IC on a working board, measured pin by pin.
- Watch for:
- Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed with a code easy to misread as 00
One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.
Codes not listed here are printed on 44 more parts.
Did you find your part?
Open this in the search to correct a character or try another package.