SMD code 02
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
104 parts are printed 02
Not sure which one you have?
Answer up to 4 quick questions and these 50 parts are ranked, with a meter test that settles it. It works on a dead part too.
FDZ3.0T1GSOD-323Zener diode, 2 pins, First SilionZener diodeSOD-3232 pinsFirst Silion
- What it is
- Zener diode
- Maker
- First Silion
- Package
- SOD-323
- Pins
- 2
- Details
- Zener diode: 2.8..3.2V, Izt=5mA, Zzt=100, 200mW
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
Gali-2SOT-89RF amplifier (MMIC), 3 pins, MCRF amplifier (MMIC)SOT-893 pinsMC
- What it is
- RF amplifier (MMIC)
- Maker
- MC
- Package
- SOT-89
- Pins
- 3
- Details
- DC-8GHz MMIC amp 16dB gain
- Source
- Published code list
Is it dead? The meter test is below: RF amplifier.
GDZ2.0BSOD-3232 pins, VishayNot recordedSOD-3232 pinsVishay
- What it is
- Not recorded
- Maker
- Vishay
- Package
- SOD-323
- Pins
- 2
- Details
- zener 200mW 2.0V
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
GDZ2V0B-VSOD-323Zener diode, 2 pins, VishayZener diodeSOD-3232 pinsVishay
- What it is
- Zener diode
- Maker
- Vishay
- Package
- SOD-323
- Pins
- 2
- Details
- Z-diode: 2.02..2.2V, Izt=5mA, Zzt=100Ω, 200mW
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
GSMM5Z3V0SOD-523Zener diode, 2 pins, Good-ArkZener diodeSOD-5232 pinsGood-Ark
- What it is
- Zener diode
- Maker
- Good-Ark
- Package
- SOD-523
- Pins
- 2
- Details
- Zener diode: 2.8..3.2V, Izt=5mA, Zzt=100, 200mW
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
HBFP-0405SOT-3234 pins, BroadcomNot recordedSOT-3234 pinsBroadcom
- What it is
- Not recorded
- Maker
- Broadcom
- Package
- SOT-323
- Pins
- 4
- Details
- High Performance Isolated Collector Silicon Bipolar Transistor
- Source
- Published code list
Is it dead? The meter test is below: Bipolar transistor.
LBZT52B2V0T1GSOD-123Zener diode, 2 pins, LRCZener diodeSOD-1232 pinsLRC
- What it is
- Zener diode
- Maker
- LRC
- Package
- SOD-123
- Pins
- 2
- Details
- Zener diode, VZ Min 2.02 V, VZ Nom 2.1 V, VZ Max 2.2 V
- Source
- An older or alternative marking, from a published code list
Is it dead? The meter test is below: Zener diode.
LUDZS2.0BT1GSOD-323Zener diode, 2 pins, LRCZener diodeSOD-3232 pinsLRC
- What it is
- Zener diode
- Maker
- LRC
- Package
- SOD-323
- Pins
- 2
- Details
- Zener diode: 2.02..2.2V, Izt=5mA, 200mW
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
MM3Z3V0T1SOD-3232 pins, MotorolaNot recordedSOD-3232 pinsMotorola
- What it is
- Not recorded
- Maker
- Motorola
- Package
- SOD-323
- Pins
- 2
- Details
- Стабилитрон (Zener)
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
MMPZ5225BPTSOD-323Zener diode, 2 pins, Chenmko EnterpriseZener diodeSOD-3232 pinsChenmko Enterprise
- What it is
- Zener diode
- Maker
- Chenmko Enterprise
- Package
- SOD-323
- Pins
- 2
- Details
- Zener diode: 2.850..3.150V, Izt=5mA, Zzt=95, 225mW
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
MRF5711SOT-1434 pins, MotNot recordedSOT-1434 pinsMot
- What it is
- Not recorded
- Maker
- Mot
- Package
- SOT-143
- Pins
- 4
- Details
- Si-npn: UHF, 20V, 80mA, 580mW, B=50..300, 8GHz
- Source
- Published code list
Is it dead? The meter test is below: This part.
MRF5711LSOT-1434 pinsNot recordedSOT-1434 pinsNot recorded
- What it is
- Not recorded
- Maker
- Not recorded
- Package
- SOT-143
- Pins
- 4
- Details
- npn RF MRF571
- Source
- Published code list
Is it dead? The meter test is below: This part.
MTN2302N3SOT-23N-channel MOSFET, 3 pinsN-channel MOSFETSOT-233 pinsNot recorded
- What it is
- N-channel MOSFET
- Maker
- Not recorded
- Package
- SOT-23
- Pins
- 3
- Details
- 20 V, 3.5 A N-channel MOSFET
- Source
- Published code list
Is it dead? The meter test is below: N-channel MOSFET.
PDTC143EESOT-4163 pins, NXPNot recordedSOT-4163 pinsNXP
- What it is
- Not recorded
- Maker
- NXP
- Package
- SOT-416
- Pins
- 3
- Details
- Si-npn-Digi: Sw, 50V, 100mA, 150mW, R1/R2=4.7k/4.7k
- Source
- Published code list
Is it dead? The meter test is below: This part.
PDTC143EKSOT-233 pinsNot recordedSOT-233 pinsNot recorded
- What it is
- Not recorded
- Maker
- Not recorded
- Package
- SOT-23
- Pins
- 3
- Details
- Si-npn-Digi: Sw, 50V, 100mA, 150mW, R1/R2=4.7k/4.7k
- Source
- Published code list
Is it dead? The meter test is below: This part.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
Zener diode
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways, forward too: failed open.
- Holds well off its rated voltage on the supply test: drifted.
- A soft knee, or a voltage that creeps on the supply test: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
RF amplifier
Voltage, board powered, on the output pin that the bias resistor or choke feeds.
Working, it reads
The output pin sits at the device voltage the datasheet gives, a few volts, below the supply.
Dead, it reads
- Output pin at 0 V, or near 0 Ω to ground with the power off: shorted inside.
- Output pin at the full supply voltage: open inside, no current flowing.
- On the board:
- Measured on the board with power on; the bias network is part of the reading.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The figures depend on the part and its bias resistor. The datasheet gives both.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Bipolar transistor
Diode range, part lifted or its base leg off the pad.
Working, it reads
From the base, one probe colour reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.
Dead, it reads
- Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
- The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
- Only one junction reads, or none: a junction has failed open. It then looks like a diode.
- A reading the wrong way round, where it should be open: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
This part
Diode range and ohms range, part lifted.
Working, it reads
Depends on what it is. The datasheet, or an identical part, says.
Dead, it reads
- Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
- Open between every pair of pins: failed open, or a part that reads open when working.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
N-channel MOSFET
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
- Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
- The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
- No body diode at all: failed open.
- On the board
- the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Did you find your part?
Open this in the search to correct a character or try another package.