SMD code 0K1
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
0K1 on a chip resistor
100 Ω
100 Ω resistor
The K is both the decimal point and the multiplier: 100 Ω.
Check it with a meter
Lift one end and measure across it. A good one reads 100 Ω. Measuring it in circuit reads the parallel combination of everything around it, which is almost always lower, never higher: well above 100 Ω on the board is a fault. Open, or well above 100 Ω, means it has failed: burnt, cracked or corroded. That does not change what to fit: the marking still says 100 Ω. A burnt resistor usually means the part it feeds drew too much, so find that before fitting a new one.
On a transistor or diode body (SOT-23-5, USP-6C, SOT-89-5), 0K1 is a part code instead. Those parts are listed below.
5 parts are printed 0K1
Not sure which one you have?
Answer up to 4 quick questions and these 5 parts are ranked, with a meter test that settles it. It works on a dead part too.
XC6101D432MRSOT-23-5Voltage supervisor, 5 pins, TorexVoltage supervisorSOT-23-55 pinsTorex
- What it is
- Voltage supervisor
- Maker
- Torex
- Package
- SOT-23-5
- Pins
- 5
- Details
- CMOS-IC: VDet 3.2V, 5%, Hst, -MR, -Reset PPO, Wt=200ms, Rt=100ms
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
XC6120N31SRSOT-23-5Voltage supervisor, 5 pins, TorexVoltage supervisorSOT-23-55 pinsTorex
- What it is
- Voltage supervisor
- Maker
- Torex
- Package
- SOT-23-5
- Pins
- 5
- Details
- Voltage detector IC: 3.1V±2%, N-ch, +Reset ODO
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
3 more parts have no package on record
SGM820C-2.3QTGT8GVoltage supervisor, 8 pins, SG MicroVoltage supervisorNot recorded8 pinsSG Micro
- What it is
- Voltage supervisor
- Maker
- SG Micro
- Package
- Not recorded
- Pins
- 8
- Details
- 2.325 V threshold, High-Accuracy Supervisory Circuit with Watchdog Timer for Automotive Applications
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Integrated circuit.
XC6120N31HVoltage supervisor, TorexVoltage supervisorNot recordedNot recordedTorex
- What it is
- Voltage supervisor
- Maker
- Torex
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Voltage detector IC: 3.1V±2%, N-ch, +Reset ODO
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
XCL210B211GR-GDC-DC converter, TorexDC-DC converterNot recordedNot recordedTorex
- What it is
- DC-DC converter
- Maker
- Torex
- Package
- Not recorded
- Pins
- Not recorded
- Details
- DC/DC voltage converter IC: PFM st-dwn, 2.1V±2%, 50mA, +CE
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
Integrated circuit
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
- A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
- Supply present, output stuck: failed, or its load has.
- On the board:
- A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
- Compare:
- The surest reference is the same IC on a working board, measured pin by pin.
- Watch for:
- Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed with a code easy to misread as 0K1
One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.
Codes that begin with 0K1
For a marking with its end worn or burnt off. Each code has a page of its own.
Did you find your part?
Open this in the search to correct a character or try another package.