SMD code 11A
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
11A on a chip resistor
127 Ω
127 Ω resistor, 1%
EIA-96 precision code: 11 stands for 127 in the E96 table, and the letter A is the multiplier, × 1. These are 1% parts.
Check it with a meter
Lift one end and measure across it. A good one reads 127 Ω within 1%. Measuring it in circuit reads the parallel combination of everything around it, which is almost always lower, never higher: well above 127 Ω on the board is a fault. Open, or well above 127 Ω, means it has failed: burnt, cracked or corroded. That does not change what to fit: the marking still says 127 Ω. A burnt resistor usually means the part it feeds drew too much, so find that before fitting a new one.
On a transistor or diode body (SOT-23-5, SMA, SMB), 11A is a part code instead. Those parts are listed below.
52 parts are printed 11A
Not sure which one you have?
Answer up to 4 quick questions and these 50 parts are ranked, with a meter test that settles it. It works on a dead part too.
MMF11ASOD-123FTVS diode, 2 pins, Shanghai SemitechTVS diodeSOD-123F2 pinsShanghai Semitech
- What it is
- TVS diode
- Maker
- Shanghai Semitech
- Package
- SOD-123F
- Pins
- 2
- Details
- Transient voltage supressor: Vrwm=11V, Vbr=12.2..14.0V, Ipp=11A, 200W(1ms)
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
P4SMAFJ11ASMAFTVS diode, 2 pins, Dongguan You Feng Wei ElectronicsTVS diodeSMAF2 pinsDongguan You Feng Wei Electronics
- What it is
- TVS diode
- Maker
- Dongguan You Feng Wei Electronics
- Package
- SMAF
- Pins
- 2
- Details
- TVS diode, unidirectional
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
P4SMFJ11ASOD-123FTVS diode, 2 pins, YeashinTVS diodeSOD-123F2 pinsYeashin
- What it is
- TVS diode
- Maker
- Yeashin
- Package
- SOD-123F
- Pins
- 2
- Details
- Transient voltage supressor: Vrwm=11V, Ipp=22A, 400W (1ms)
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
P1100SAASMA2 pins, VishayNot recordedSMA2 pinsVishay
- What it is
- Not recorded
- Maker
- Vishay
- Package
- SMA
- Pins
- 2
- Details
- Thyristor surge protector: Vdrm=90V, Vs=130V, Ipp=35A(1ms), Bidir.
- Source
- Published code list
Is it dead? The meter test is below: This part.
PSMAJ11ASMATVS diode, 2 pins, Lite-On SemiconductorTVS diodeSMA2 pinsLite-On Semiconductor
- What it is
- TVS diode
- Maker
- Lite-On Semiconductor
- Package
- SMA
- Pins
- 2
- Details
- Transient voltage supressor: Vrwm=9.4V, Vbr=10.5..11.6V, Ipp=25.6A, 400W(1ms)
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
PSMBJ11ASMBTVS diode, 2 pins, Lite-On SemiconductorTVS diodeSMB2 pinsLite-On Semiconductor
- What it is
- TVS diode
- Maker
- Lite-On Semiconductor
- Package
- SMB
- Pins
- 2
- Details
- Transient voltage supressor: Vrwm=9.4V, Vbr=10.5..11.6V, Ipp=38.5A, 600W(1ms)
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
PSMCJ11ASMCTVS diode, 2 pins, Lite-On SemiconductorTVS diodeSMC2 pinsLite-On Semiconductor
- What it is
- TVS diode
- Maker
- Lite-On Semiconductor
- Package
- SMC
- Pins
- 2
- Details
- Transient voltage supressor: Vrwm=9.4V, Vbr=10.5..11.6V, Ipp=96.2A, 1500W(1ms)
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
PZM11NB2ASOT-233 pins, NXPNot recordedSOT-233 pinsNXP
- What it is
- Not recorded
- Maker
- NXP
- Package
- SOT-23
- Pins
- 3
- Details
- dual ca 11V 0.3W zener
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
SMA6F11ASMATVS diode, 2 pins, Bruckewell TechnologyTVS diodeSMA2 pinsBruckewell Technology
- What it is
- TVS diode
- Maker
- Bruckewell Technology
- Package
- SMA
- Pins
- 2
- Details
- 600 W TVS diode, unidirectional
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
SMAJ11ASMATVS diode, 2 pins, SynSemiTVS diodeSMA2 pinsSynSemi
- What it is
- TVS diode
- Maker
- SynSemi
- Package
- SMA
- Pins
- 2
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
SMAJP4KE11ASMATVS diode, 2 pins, Micro Commercial ComponentsTVS diodeSMA2 pinsMicro Commercial Components
- What it is
- TVS diode
- Maker
- Micro Commercial Components
- Package
- SMA
- Pins
- 2
- Details
- Transient voltage supressor: Vrwm=9.40V, Vbr=10.50..11.60V, Ipp=26.3A, 400W(1ms)
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
SMBG11ASMBGTVS diode, 2 pins, Microsemi Integrated Products DivisionTVS diodeSMBG2 pinsMicrosemi Integrated Products Division
- What it is
- TVS diode
- Maker
- Microsemi Integrated Products Division
- Package
- SMBG
- Pins
- 2
- Details
- 600 W TVS diode, unidirectional
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
SMBJP6KE11ASMBTVS diode, 2 pins, Micro Commercial ComponentsTVS diodeSMB2 pinsMicro Commercial Components
- What it is
- TVS diode
- Maker
- Micro Commercial Components
- Package
- SMB
- Pins
- 2
- Details
- Transient voltage supressor: Vrwm=9.40V, Vbr=10.50..11.60V, Ipp=39.1A, 600W(1ms)
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
SMCJ1.5KE11ASMCTVS diode, 2 pins, Micro Commercial ComponentsTVS diodeSMC2 pinsMicro Commercial Components
- What it is
- TVS diode
- Maker
- Micro Commercial Components
- Package
- SMC
- Pins
- 2
- Details
- Transient voltage supressor: Vrwm=9.40V, Vbr=10.50..11.60V, Ipp=97.4A, 1500W(1ms)
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
1 more part has no package on record
RKZ11AKUZener diode, RenesasZener diodeNot recordedNot recordedRenesas
- What it is
- Zener diode
- Maker
- Renesas
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Zener diode: 10.18..10.71V, Izt=10mA, Zzt=30, 500mW
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
TVS or ESD protection diode
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
- From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
- A reading both ways on a one-way part: leaky.
- A one-way part open both ways: failed open.
- On the board
- , a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
- Compare:
- The same part on the next line or connector pin is the healthy reading to compare with.
- Watch for:
- A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
This part
Diode range and ohms range, part lifted.
Working, it reads
Depends on what it is. The datasheet, or an identical part, says.
Dead, it reads
- Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
- Open between every pair of pins: failed open, or a part that reads open when working.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Zener diode
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways, forward too: failed open.
- Holds well off its rated voltage on the supply test: drifted.
- A soft knee, or a voltage that creeps on the supply test: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Did you find your part?
Open this in the search to correct a character or try another package.