SMD code 1216
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
1216 on a chip resistor
121 MΩ
121 MΩ resistor, 1%
121 followed by 6 zeros. Four digits is normally the 1% series.
Check it with a meter
Lift one end and measure across it. A good one reads 121 MΩ within 1%. Measuring it in circuit reads the parallel combination of everything around it, which is almost always lower, never higher: well above 121 MΩ on the board is a fault. Open, or well above 121 MΩ, means it has failed: burnt, cracked or corroded. That does not change what to fit: the marking still says 121 MΩ. A burnt resistor usually means the part it feeds drew too much, so find that before fitting a new one.
On a transistor or diode body (DFN, SOT-23, SOT-23-5), 1216 is a part code instead. Those parts are listed below.
6 parts are printed 1216
Not sure which one you have?
Answer up to 4 quick questions and these 6 parts are ranked, with a meter test that settles it. It works on a dead part too.
BL1216DF1DFNP-channel MOSFET, Galaxy MicroelectronicsP-channel MOSFETDFNNot recordedGalaxy Microelectronics
- What it is
- P-channel MOSFET
- Maker
- Galaxy Microelectronics
- Package
- DFN
- Pins
- Not recorded
- Details
- -15V, P Channel MOSFETs
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: P-channel MOSFET.
TBL1216-6LSOT-23-6P-channel MOSFET, 6 pins, Galaxy MicroelectronicsP-channel MOSFETSOT-23-66 pinsGalaxy Microelectronics
- What it is
- P-channel MOSFET
- Maker
- Galaxy Microelectronics
- Package
- SOT-23-6
- Pins
- 6
- Details
- 8A, 15V, 2W, P Channel, Power MOSFETs
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: P-channel MOSFET.
TBL1216DF1DFNP-channel MOSFET, Galaxy MicroelectronicsP-channel MOSFETDFNNot recordedGalaxy Microelectronics
- What it is
- P-channel MOSFET
- Maker
- Galaxy Microelectronics
- Package
- DFN
- Pins
- Not recorded
- Details
- -15V, P Channel MOSFETs
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: P-channel MOSFET.
WM02P60M2SOT-233 pins, WayonNot recordedSOT-233 pinsWayon
- What it is
- Not recorded
- Maker
- Wayon
- Package
- SOT-23
- Pins
- 3
- Details
- MOSFET
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: MOSFET.
WM02P160RDFNWayonNot recordedDFNNot recordedWayon
- What it is
- Not recorded
- Maker
- Wayon
- Package
- DFN
- Pins
- Not recorded
- Details
- MOSFET
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: MOSFET.
1 more part has no package on record
CJM1216P-channel MOSFET, JSCJP-channel MOSFETNot recordedNot recordedJSCJ
- What it is
- P-channel MOSFET
- Maker
- JSCJ
- Package
- Not recorded
- Pins
- Not recorded
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: P-channel MOSFET.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
P-channel MOSFET
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the drain, black on the source: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
- Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
- The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
- No body diode at all: failed open.
- On the board
- the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. Lift a leg to be sure.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
MOSFET
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
- Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
- The gate reads low to source or drain: gate shorted.
- No body diode at all: failed open.
- On the board
- the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed with a code easy to misread as 1216
One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.
Codes that begin with 1216
For a marking with its end worn or burnt off. Each code has a page of its own.
Did you find your part?
Open this in the search to correct a character or try another package.