Skip to content

SMD code 12A

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

12A on a chip resistor

130 Ω

130 Ω resistor, 1%

EIA-96 precision code: 12 stands for 130 in the E96 table, and the letter A is the multiplier, × 1. These are 1% parts.

Check it with a meter

Lift one end and measure across it. A good one reads 130 Ω within 1%. Measuring it in circuit reads the parallel combination of everything around it, which is almost always lower, never higher: well above 130 Ω on the board is a fault. Open, or well above 130 Ω, means it has failed: burnt, cracked or corroded. That does not change what to fit: the marking still says 130 Ω. A burnt resistor usually means the part it feeds drew too much, so find that before fitting a new one.

On a transistor or diode body (SMA, SMB, SOT-23), 12A is a part code instead. Those parts are listed below.

Not sure which one you have?

Answer up to 4 quick questions and these 50 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • SMA6F12ASMATVS diode, 2 pins, Bruckewell TechnologyTVS diodeSMA2 pinsBruckewell Technology
    What it is
    TVS diode
    Maker
    Bruckewell Technology
    Package
    SMA
    Pins
    2
    Details
    600 W TVS diode, unidirectional
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • SMAJ12ASMATVS diode, 2 pins, SynSemiTVS diodeSMA2 pinsSynSemi
    What it is
    TVS diode
    Maker
    SynSemi
    Package
    SMA
    Pins
    2
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • SMAJP4KE12ASMATVS diode, 2 pins, Micro Commercial ComponentsTVS diodeSMA2 pinsMicro Commercial Components
    What it is
    TVS diode
    Maker
    Micro Commercial Components
    Package
    SMA
    Pins
    2
    Details
    Transient voltage supressor: Vrwm=10.20V, Vbr=11.40..12.60V, Ipp=24.6A, 400W(1ms)
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • SMBG12ASMBGTVS diode, 2 pins, Microsemi Integrated Products DivisionTVS diodeSMBG2 pinsMicrosemi Integrated Products Division
    What it is
    TVS diode
    Maker
    Microsemi Integrated Products Division
    Package
    SMBG
    Pins
    2
    Details
    600 W TVS diode, unidirectional
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • SMBJP6KE12ASMBTVS diode, 2 pins, Micro Commercial ComponentsTVS diodeSMB2 pinsMicro Commercial Components
    What it is
    TVS diode
    Maker
    Micro Commercial Components
    Package
    SMB
    Pins
    2
    Details
    Transient voltage supressor: Vrwm=10.20V, Vbr=11.40..12.60V, Ipp=36.5A, 600W(1ms)
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • SMCJ1.5KE12ASMCTVS diode, 2 pins, Micro Commercial ComponentsTVS diodeSMC2 pinsMicro Commercial Components
    What it is
    TVS diode
    Maker
    Micro Commercial Components
    Package
    SMC
    Pins
    2
    Details
    Transient voltage supressor: Vrwm=10.20V, Vbr=11.40..12.60V, Ipp=91.0A, 1500W(1ms)
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • SMCJ12ASMCTVS diode, 2 pins, SynSemiTVS diodeSMC2 pinsSynSemi
    What it is
    TVS diode
    Maker
    SynSemi
    Package
    SMC
    Pins
    2
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • STBP112ATDFN8 pins, STMicroelectronicsNot recordedDFN8 pinsSTMicroelectronics
    What it is
    Not recorded
    Maker
    STMicroelectronics
    Package
    DFN
    Pins
    8
    Source
    Published code list

    Is it dead? The meter test is below: This part.

  • STD123SSOT-23NPN transistor, 3 pins, Kodenshi AUKNPN transistorSOT-233 pinsKodenshi AUK
    What it is
    NPN transistor
    Maker
    Kodenshi AUK
    Package
    SOT-23
    Pins
    3
    Details
    NPN bipolar transistor
    Source
    Published code list

    Is it dead? The meter test is below: NPN transistor.

  • TV15CJ120A-GSMCTVS diode, 2 pins, ComchipTVS diodeSMC2 pinsComchip
    What it is
    TVS diode
    Maker
    Comchip
    Package
    SMC
    Pins
    2
    Details
    Transient voltage supressor: Vbr=11.4..12.6V, Vrwm=10.2V, Ipp=89.82A, 1500W(1ms)
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • TVP04A120A-GSMATVS diode, 2 pins, ComchipTVS diodeSMA2 pinsComchip
    What it is
    TVS diode
    Maker
    Comchip
    Package
    SMA
    Pins
    2
    Details
    Transient voltage supressor: Vbr=11.40..12.60V, Vrwm=10.2V, Ipp=23.95A, 400W(1ms)
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • TVP06B12A-GSMBTVS diode, 2 pins, ComchipTVS diodeSMB2 pinsComchip
    What it is
    TVS diode
    Maker
    Comchip
    Package
    SMB
    Pins
    2
    Details
    Transient voltage supressor: Vrwm=10.2V, Vbr=11.40..12.60V, Ipp=35.93A, 600W(1ms)
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • 3 more parts have no package on record
    • SMD12ALPTSchottky diode, Chenmko EnterpriseSchottky diodeNot recordedNot recordedChenmko Enterprise
      What it is
      Schottky diode
      Maker
      Chenmko Enterprise
      Package
      Not recorded
      Pins
      Not recorded
      Details
      Diode: SBR, 20V, 1A, Vf<0.38V(1A)
      Source
      Published code list

      Is it dead? The meter test is below: Schottky diode.

    • STD123ASFAUK SemiconductorNot recordedNot recordedNot recordedAUK Semiconductor
      What it is
      Not recorded
      Maker
      AUK Semiconductor
      Package
      Not recorded
      Pins
      Not recorded
      Details
      Si-npn: Hi-beta, Lo-sat, 10V, 1A, 350mW, B>400, 260MHz
      Source
      Published code list

      Is it dead? The meter test is below: This part.

    • SZP6SMB12ATVS diode, onsemiTVS diodeNot recordedNot recordedonsemi
      What it is
      TVS diode
      Maker
      onsemi
      Package
      Not recorded
      Pins
      Not recorded
      Details
      Transient voltage supressor: Vrwm=12V, Vbr=11.4..12.6V, 35.9A, 600W(1ms)
      Source
      Published code list

      Is it dead? The meter test is below: TVS or ESD protection diode.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

TVS or ESD protection diode

Diode range, from the protected line to ground, part lifted if you can.

Working, it reads

A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.

Dead, it reads

  • From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  • A reading both ways on a one-way part: leaky.
  • A one-way part open both ways: failed open.
On the board
, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Schottky diode

Diode range, part lifted or one leg off the pad. Red probe on the anode.

Working, it reads

About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • A reading the wrong way round as well: leaky.
  • Open both ways: failed open.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

This part

Diode range and ohms range, part lifted.

Working, it reads

Depends on what it is. The datasheet, or an identical part, says.

Dead, it reads

  • Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
  • Open between every pair of pins: failed open, or a part that reads open when working.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

NPN transistor

Diode range, part lifted or its base leg off the pad.

Working, it reads

Red probe on the base reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.

Dead, it reads

  • Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
  • The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
  • Only one junction reads, or none: a junction has failed open. It then looks like a diode.
  • A reading the wrong way round, where it should be open: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Did you find your part?

Open this in the search to correct a character or try another package.