Skip to content

SMD code 13B

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

13B on a chip resistor

1.33 kΩ

1.33 kΩ resistor, 1%

EIA-96 precision code: 13 stands for 133 in the E96 table, and the letter B is the multiplier, × 10. These are 1% parts.

Check it with a meter

Lift one end and measure across it. A good one reads 1.33 kΩ within 1%. Measuring it in circuit reads the parallel combination of everything around it, which is almost always lower, never higher: well above 1.33 kΩ on the board is a fault. Open, or well above 1.33 kΩ, means it has failed: burnt, cracked or corroded. That does not change what to fit: the marking still says 1.33 kΩ. A burnt resistor usually means the part it feeds drew too much, so find that before fitting a new one.

On a transistor or diode body (SOT-23-5, SOT-23, SOT-89-5), 13B is a part code instead. Those parts are listed below.

Not sure which one you have?

Answer up to 4 quick questions and these 23 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • 1SMB3EZ13SMBZener diode, 2 pins, PanjitZener diodeSMB2 pinsPanjit
    What it is
    Zener diode
    Maker
    Panjit
    Package
    SMB
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • CHBZ13BGPSOT-23Zener diode, 3 pins, ChenmkoZener diodeSOT-233 pinsChenmko
    What it is
    Zener diode
    Maker
    Chenmko
    Package
    SOT-23
    Pins
    3
    Details
    DUAL SILICON PLANAR POWER ZENER DIODES, 2.4 V
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • PDZV13BSOD-128Zener diode, 2 pins, ROHMZener diodeSOD-1282 pinsROHM
    What it is
    Zener diode
    Maker
    ROHM
    Package
    SOD-128
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • PDZVTF13BSOD-128Zener diode, 2 pins, ROHMZener diodeSOD-1282 pinsROHM
    What it is
    Zener diode
    Maker
    ROHM
    Package
    SOD-128
    Pins
    2
    Details
    Zener Diode (AEC-Q101 qualified)
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • PTZ13BMELFZener diode, 2 pins, ROHMZener diodeMELF2 pinsROHM
    What it is
    Zener diode
    Maker
    ROHM
    Package
    MELF
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • TLZ13BSOD-80Zener diode, 2 pins, Taitron ComponentsZener diodeSOD-802 pinsTaitron Components
    What it is
    Zener diode
    Maker
    Taitron Components
    Package
    SOD-80
    Pins
    2
    Details
    SMD Zener Diodes (Leadless ) - 500mW
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • Z3SMB13BSMBZener diode, 2 pins, Taitron ComponentsZener diodeSMB2 pinsTaitron Components
    What it is
    Zener diode
    Maker
    Taitron Components
    Package
    SMB
    Pins
    2
    Details
    SMD Zener Diodes (Two Terminals)- 3W
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • 1SMA5913BSMAZener diode, 2 pins, RectronZener diodeSMA2 pinsRectron
    What it is
    Zener diode
    Maker
    Rectron
    Package
    SMA
    Pins
    2
    Details
    1.5 Watt Plastic Surface Mount Zener Voltage Regulators 1SMA59xxBT3G Series, SZ1SMA59xxBT3G Series
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • APR3013-17ASOT-233 pins, AnpecNot recordedSOT-233 pinsAnpec
    What it is
    Not recorded
    Maker
    Anpec
    Package
    SOT-23
    Pins
    3
    Details
    CMOS-IC: Voltage detector, 1.75V, -Reset Open drain output
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • APR3013-17BSOT-23-55 pins, AnpecNot recordedSOT-23-55 pinsAnpec
    What it is
    Not recorded
    Maker
    Anpec
    Package
    SOT-23-5
    Pins
    5
    Details
    CMOS-IC: Voltage detector, 1.75V, -Reset Open drain output
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • APR3013-17DSOT-893 pins, AnpecNot recordedSOT-893 pinsAnpec
    What it is
    Not recorded
    Maker
    Anpec
    Package
    SOT-89
    Pins
    3
    Details
    CMOS-IC: Voltage detector, 1.75V, -Reset Open drain output
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • GLZ13BSOD-80Zener diode, 2 pins, PanjitZener diodeSOD-802 pinsPanjit
    What it is
    Zener diode
    Maker
    Panjit
    Package
    SOD-80
    Pins
    2
    Details
    Zener diode: 12.55..13.21V, Zzt=14 , Izt=10mA, 500mW
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • 3 more parts have no package on record
    • 1SMB3EZ13-AUZener diode, PanjitZener diodeNot recordedNot recordedPanjit
      What it is
      Zener diode
      Maker
      Panjit
      Package
      Not recorded
      Pins
      Not recorded
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Zener diode.

    • PLZ13BZener diode, VishayZener diodeNot recordedNot recordedVishay
      What it is
      Zener diode
      Maker
      Vishay
      Package
      Not recorded
      Pins
      Not recorded
      Details
      13 V Zener diode
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Zener diode.

    • PTZTF13BZener diode, ROHMZener diodeNot recordedNot recordedROHM
      What it is
      Zener diode
      Maker
      ROHM
      Package
      Not recorded
      Pins
      Not recorded
      Details
      Zener Diode (AEC-Q101 qualified)
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Zener diode.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

Zener diode

Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.

Working, it reads

About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • Open both ways, forward too: failed open.
  • Holds well off its rated voltage on the supply test: drifted.
  • A soft knee, or a voltage that creeps on the supply test: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Integrated circuit

Voltage with the board powered; ohms from each pin to ground with it off.

Working, it reads

Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.

Dead, it reads

  • A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  • Supply present, output stuck: failed, or its load has.
On the board:
A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
Compare:
The surest reference is the same IC on a working board, measured pin by pin.
Watch for:
Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Printed with a code easy to misread as 13B

One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.

Did you find your part?

Open this in the search to correct a character or try another package.