SMD code 2066
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
4 parts are printed 2066
Not sure which one you have?
Answer up to 4 quick questions and these 4 parts are ranked, with a meter test that settles it. It works on a dead part too.
TPS2066DSOT-23Load switch, 3 pins, Texas InstrumentsLoad switch3 pinsTexas Instruments
- What it is
- Load switch
- Maker
- Texas Instruments
- Package
- SOT-23
- Pins
- 3
- Details
- Power switch
- Source
- Published code list
Is it dead? The meter test is below: Load switch.
TPS2066DGNSOT-23Load switch, 3 pins, Texas InstrumentsLoad switch3 pinsTexas Instruments
- What it is
- Load switch
- Maker
- Texas Instruments
- Package
- SOT-23
- Pins
- 3
- Details
- Power switch
- Source
- Published code list
Is it dead? The meter test is below: Load switch.
2 more parts have no package on record
G2066L71UMotor driver, 10 pins, Global Mixed-mode TechnologyMotor driver10 pinsGlobal Mixed-mode Technology
- What it is
- Motor driver
- Maker
- Global Mixed-mode Technology
- Package
- Not recorded
- Pins
- 10
- Details
- CLAF-Like Plus (Close Loop Auto Focus-Like Plus) VCM Driver for Smart Phone
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Integrated circuit.
SGM2066XTDE8G8 pins, SG MicroNot recorded8 pinsSG Micro
- What it is
- Not recorded
- Maker
- SG Micro
- Package
- Not recorded
- Pins
- 8
- Details
- Low-Noise Regulated, Switched-Capacitor Voltage Inverter
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Ceramic capacitor.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
Integrated circuit
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
- A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
- Supply present, output stuck: failed, or its load has.
- On the board:
- A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
- Compare:
- The surest reference is the same IC on a working board, measured pin by pin.
- Watch for:
- Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Ceramic capacitor
Ohms range across it, and a capacitance range with it lifted.
Working, it reads
On the ohms range it reads open, or climbs to open as it charges. Lifted, a capacitance range reads close to its value.
Dead, it reads
- Near 0 Ω, or a few ohms: shorted. The usual failure, often from a crack caused by board flex or heat, and it can come and go.
- A steady resistance, kilohms rather than open: cracked and leaking.
- Lifted, far below its value on a capacitance range: cracked open or drifted. Less common than a short, but it happens.
- On the board
- a shorted capacitor shorts its whole rail, so every capacitor on that rail reads the same short. Lift one end, or feed the rail from a current-limited supply and feel which part warms up.
- Compare:
- Chip capacitors are mostly unmarked, so the value comes from the schematic or the same position on a working board.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Load switch
Voltage, board powered, black probe on ground.
Working, it reads
Switched on, the output pin sits at the input voltage. Switched off, it sits near 0 V.
Dead, it reads
- Output at the input voltage while switched off: the pass element has shorted.
- Input present and switched on, no output: failed open, or shut down into a shorted load. Power off and measure output to ground.
- On the board:
- An output near 0 Ω to ground is usually the load. Lift the output pin to see which.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The pinout and whether the enable is active high or low differ between parts. The datasheet gives both.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Codes that begin with 2066
For a marking with its end worn or burnt off. Each code has a page of its own.
Did you find your part?
Open this in the search to correct a character or try another package.