Skip to content

SMD code 20B in SMA

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

3 parts in SMA are printed 20B

Not sure which one you have?

Answer up to 4 quick questions and these 8 parts are ranked, with a meter test that settles it. It works on a dead part too.

Zener diode. What differs:

  • SMAZ5920BSMA2 pins, Vishay2 pinsVishay
    What it is
    Zener diode
    Maker
    Vishay
    Package
    SMA
    Pins
    2
    Details
    6.2 V Zener diode
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • 1SMA5920BSMA2 pins, Rectron2 pinsRectron
    What it is
    Zener diode
    Maker
    Rectron
    Package
    SMA
    Pins
    2
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • SMAJ5920BSMA2 pins, Micro Commercial Components2 pinsMicro Commercial Components
    What it is
    Zener diode
    Maker
    Micro Commercial Components
    Package
    SMA
    Pins
    2
    Details
    6.2V, 5%, Surface Mount Zener Diodes
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • 5 more parts have no package on record. Nothing rules them out, so they stay.
    • 1SMB3EZ20-AUPanjitNot recordedPanjit
      What it is
      Zener diode
      Maker
      Panjit
      Package
      Not recorded
      Pins
      Not recorded
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Zener diode.

    • PLZ20BVishayNot recordedVishay
      What it is
      Zener diode
      Maker
      Vishay
      Package
      Not recorded
      Pins
      Not recorded
      Details
      20 V Zener diode
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Zener diode.

    • SMPZ3920BVishayNot recordedVishay
      What it is
      Zener diode
      Maker
      Vishay
      Package
      Not recorded
      Pins
      Not recorded
      Details
      6.2 V Zener diode
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Zener diode.

    • HZF20BPRenesasNot recordedRenesas
      What it is
      Zener diode
      Maker
      Renesas
      Package
      Not recorded
      Pins
      Not recorded
      Details
      Z-diode: 20V±5%, 900mW
      Source
      Published code list

      Is it dead? The meter test is below: Zener diode.

    • RKZ20BKURenesasNot recordedRenesas
      What it is
      Zener diode
      Maker
      Renesas
      Package
      Not recorded
      Pins
      Not recorded
      Details
      Zener diode: 18.63..19.59V, Izt=10mA, Zzt=50, 500mW
      Source
      Published code list

      Is it dead? The meter test is below: Zener diode.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

Zener diode

Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.

Working, it reads

About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • Open both ways, forward too: failed open.
  • Holds well off its rated voltage on the supply test: drifted.
  • A soft knee, or a voltage that creeps on the supply test: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Printed with a code easy to misread as 20B

One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.

Codes that begin with 20B

For a marking with its end worn or burnt off. Each code has a page of its own.

Did you find your part?

Open this in the search to correct a character or try another package.