SMD code 2132
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
2 parts are printed 2132
Not sure which one you have?
Answer up to 4 quick questions and these 2 parts are ranked, with a meter test that settles it. It works on a dead part too.
G2132K21UDFN10 pins, Global Mixed-mode TechnologyNot recordedDFN10 pinsGlobal Mixed-mode Technology
- What it is
- Not recorded
- Maker
- Global Mixed-mode Technology
- Package
- DFN
- Pins
- 10
- Details
- Photoflash Capacitor Charger for DSC Feature VCC 2.9V to 5.5V Supply Voltage Operating Range. Suitable voltage range for
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Ceramic capacitor.
GSFC2307LSOT-23P-channel MOSFET, 3 pins, Good-ArkP-channel MOSFETSOT-233 pinsGood-Ark
- What it is
- P-channel MOSFET
- Maker
- Good-Ark
- Package
- SOT-23
- Pins
- 3
- Details
- P-channel MOSFET, 20 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: P-channel MOSFET.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
Ceramic capacitor
Ohms range across it, and a capacitance range with it lifted.
Working, it reads
On the ohms range it reads open, or climbs to open as it charges. Lifted, a capacitance range reads close to its value.
Dead, it reads
- Near 0 Ω, or a few ohms: shorted. The usual failure, often from a crack caused by board flex or heat, and it can come and go.
- A steady resistance, kilohms rather than open: cracked and leaking.
- Lifted, far below its value on a capacitance range: cracked open or drifted. Less common than a short, but it happens.
- On the board
- a shorted capacitor shorts its whole rail, so every capacitor on that rail reads the same short. Lift one end, or feed the rail from a current-limited supply and feel which part warms up.
- Compare:
- Chip capacitors are mostly unmarked, so the value comes from the schematic or the same position on a working board.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
P-channel MOSFET
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the drain, black on the source: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
- Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
- The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
- No body diode at all: failed open.
- On the board
- the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. Lift a leg to be sure.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Codes that begin with 2132
For a marking with its end worn or burnt off. Each code has a page of its own.
Did you find your part?
Open this in the search to correct a character or try another package.