Skip to content

SMD code 24 in SOT-23

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

Not sure which one you have?

Answer up to 4 quick questions and these 50 parts are ranked, with a meter test that settles it. It works on a dead part too.

all SOT-23, 3 pins. What differs:

  • ADTC114ECA-HFSOT-23Digital transistor (NPN, resistors built in), ComchipDigital transistor (NPN, resistors built in)Comchip
    What it is
    Digital transistor (NPN, resistors built in)
    Maker
    Comchip
    Package
    SOT-23
    Pins
    3
    Details
    NPN digital transistor, R1 10 kΩ, R2 10 kΩ
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Digital transistor.

  • BF556ASOT-23JFET, NXPJFETNXP
    What it is
    JFET
    Maker
    NXP
    Package
    SOT-23
    Pins
    3
    Details
    N-channel silicon junction field-effect transistors
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: JFET.

  • DDTC114ECA-7-FSOT-23Digital transistor (NPN, resistors built in), HXYDigital transistor (NPN, resistors built in)HXY
    What it is
    Digital transistor (NPN, resistors built in)
    Maker
    HXY
    Package
    SOT-23
    Pins
    3
    Details
    Digital transistor (bias resistors built in)
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Digital transistor.

  • DTC114ECASOT-23Digital transistor (NPN, resistors built in), Formosa MicrosemiDigital transistor (NPN, resistors built in)Formosa Microsemi
    What it is
    Digital transistor (NPN, resistors built in)
    Maker
    Formosa Microsemi
    Package
    SOT-23
    Pins
    3
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Digital transistor.

  • DTC114ECA-HFSOT-23Digital transistor (NPN, resistors built in), ComchipDigital transistor (NPN, resistors built in)Comchip
    What it is
    Digital transistor (NPN, resistors built in)
    Maker
    Comchip
    Package
    SOT-23
    Pins
    3
    Details
    NPN digital transistor, R1 10 kΩ, R2 10 kΩ
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Digital transistor.

  • DTC114ECA-Q1SOT-23Digital transistor (NPN, resistors built in), Formosa MicrosemiDigital transistor (NPN, resistors built in)Formosa Microsemi
    What it is
    Digital transistor (NPN, resistors built in)
    Maker
    Formosa Microsemi
    Package
    SOT-23
    Pins
    3
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Digital transistor.

  • DTC114ECACRSOT-23Digital transistor (resistors built in), SeCoSDigital transistor (resistors built in)SeCoS
    What it is
    Digital transistor (resistors built in)
    Maker
    SeCoS
    Package
    SOT-23
    Pins
    3
    Details
    Digital (resistor-equipped) transistor
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Digital transistor.

  • DTC114ECAQSOT-23Digital transistor (resistors built in), Yangjie Electronic TechDigital transistor (resistors built in)Yangjie Electronic Tech
    What it is
    Digital transistor (resistors built in)
    Maker
    Yangjie Electronic Tech
    Package
    SOT-23
    Pins
    3
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Digital transistor.

  • DTC114EKASOT-23Digital transistor (NPN, resistors built in), JSCJDigital transistor (NPN, resistors built in)JSCJ
    What it is
    Digital transistor (NPN, resistors built in)
    Maker
    JSCJ
    Package
    SOT-23
    Pins
    3
    Details
    NPN digital transistor (bias resistors built in)
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Digital transistor.

  • DTD114ECT116SOT-23Digital transistor (NPN, resistors built in), HXYDigital transistor (NPN, resistors built in)HXY
    What it is
    Digital transistor (NPN, resistors built in)
    Maker
    HXY
    Package
    SOT-23
    Pins
    3
    Details
    Digital transistor (bias resistors built in)
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Digital transistor.

  • EMB80P03JSOT-23P-channel MOSFET, Excelliance MOSP-channel MOSFETExcelliance MOS
    What it is
    P-channel MOSFET
    Maker
    Excelliance MOS
    Package
    SOT-23
    Pins
    3
    Details
    30 V, 3.6 A P-channel MOSFET
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: P-channel MOSFET.

  • EMB80P03JSSOT-23P-channel MOSFET, Excelliance MOSP-channel MOSFETExcelliance MOS
    What it is
    P-channel MOSFET
    Maker
    Excelliance MOS
    Package
    SOT-23
    Pins
    3
    Details
    30 V, 3.6 A P-channel MOSFET
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: P-channel MOSFET.

  • GSOT24-E3-08SOT-23TVS diode, UMWTVS diodeUMW
    What it is
    TVS diode
    Maker
    UMW
    Package
    SOT-23
    Pins
    3
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • HDTD114ECT116SOT-23Digital transistor (NPN, resistors built in), HXYDigital transistor (NPN, resistors built in)HXY
    What it is
    Digital transistor (NPN, resistors built in)
    Maker
    HXY
    Package
    SOT-23
    Pins
    3
    Details
    Digital transistor (bias resistors built in)
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Digital transistor.

  • MMBD1201SOT-23Switching diode, Taitron ComponentsSwitching diodeTaitron Components
    What it is
    Switching diode
    Maker
    Taitron Components
    Package
    SOT-23
    Pins
    3
    Details
    0.6A, 100V, Surface Mount Small Signal Switching Diodes
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Silicon diode.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

Digital transistor

Ohms range, part lifted. The datasheet gives the built-in resistors: R1 in series with the base, R2 from base to emitter.

Working, it reads

Base to emitter reads about R1 plus R2 either way round, about 20 kΩ on a 10 k and 10 k part, give or take their wide tolerance. Collector to emitter reads open. A part with no R2 reads a junction behind R1 one way instead.

Dead, it reads

  • Collector to emitter the same both ways, near 0 Ω with a continuous beep: shorted.
  • From the base, open or far above R1 plus R2: R1 has failed. Static damage shows here most often.
  • Base to emitter near 0 Ω: failed short.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
The readings depend on the resistor values, so an identical part elsewhere on the board is the surest reference. Measure it the same way.
Watch for:
On the diode range a good part with 10 kΩ resistors reads open on every pair, so a good part looks dead there. Use the ohms range.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

JFET

Ohms range for drain to source, diode range for the gate, part lifted.

Working, it reads

Drain to source conducts both ways at a few hundred ohms, depending on the part, and some meters beep on it. The gate reads one junction to drain and to source, about 0.6 to 0.7 V, and open the other way.

Dead, it reads

  • The gate the same both ways to drain or source, near 0 V with a continuous beep: gate shorted.
  • Drain to source open: the channel has failed open.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
Drain to source resistance varies from part to part. An identical part elsewhere on the board shows what is normal.
Watch for:
A good channel can beep like a short between drain and source. That is normal; the gate junction says whether it has failed.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Digital transistor

Ohms range, part lifted. The datasheet gives the built-in resistors: R1 in series with the base, R2 from base to emitter.

Working, it reads

Base to emitter reads about R1 plus R2 either way round, about 20 kΩ on a 10 k and 10 k part, give or take their wide tolerance. Collector to emitter reads open. A part with no R2 reads a junction behind R1 one way instead.

Dead, it reads

  • Collector to emitter the same both ways, near 0 Ω with a continuous beep: shorted.
  • From the base, open or far above R1 plus R2: R1 has failed. Static damage shows here most often.
  • Base to emitter near 0 Ω: failed short.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
The readings depend on the resistor values, so an identical part elsewhere on the board is the surest reference. Measure it the same way.
Watch for:
On the diode range a good part with 10 kΩ resistors reads open on every pair, so a good part looks dead there. Use the ohms range.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

P-channel MOSFET

Diode range, part lifted. Test drain to source first, then short gate to source and test again.

Working, it reads

Red probe on the drain, black on the source: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.

Dead, it reads

  • Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  • The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
  • No body diode at all: failed open.
On the board
the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

TVS or ESD protection diode

Diode range, from the protected line to ground, part lifted if you can.

Working, it reads

A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.

Dead, it reads

  • From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  • A reading both ways on a one-way part: leaky.
  • A one-way part open both ways: failed open.
On the board
, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Silicon diode

Diode range, part lifted or one leg off the pad. Red probe on the anode.

Working, it reads

About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • Open both ways: failed open.
  • A reading the wrong way round as well: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Printed with a code easy to misread as 24

One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.

Codes not listed here are printed on 8 more parts.

Did you find your part?

Open this in the search to correct a character or try another package.