Skip to content

SMD code 349B

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

349B is a capacitor marking

3.4 pF

3.4 pF capacitor

34 followed by the multiplier 9, in picofarads: 3.4 pF. Printed this way on film and larger ceramic capacitors; small chip ceramics are usually not printed at all. B is the tolerance, ±0.1 pF.

Check it with a meter

Lift one end and measure it on a capacitance range. A good one reads close to 3.4 pF. In circuit the meter also sees everything connected across it, so the reading means little until it is out. A failed one usually reads near 0 Ω, or a steady low resistance, on the ohms range, often from a crack. On the board a shorted capacitor shorts its whole rail. A failed reading does not change what to fit: the marking still says 3.4 pF.

On a transistor or diode body (SMC, SMB, SOT-23), 349B is a part code instead. Those parts are listed below.

16 parts are printed 349B

Not sure which one you have?

Answer up to 4 quick questions and these 16 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • 1SMC5349SMCZener diode, 2 pins, PanjitZener diodeSMC2 pinsPanjit
    What it is
    Zener diode
    Maker
    Panjit
    Package
    SMC
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • 1SMC5349-AUSMCZener diode, 2 pins, PanjitZener diodeSMC2 pinsPanjit
    What it is
    Zener diode
    Maker
    Panjit
    Package
    SMC
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • 1SMC5349BSMCZener diode, 2 pins, YFWZener diodeSMC2 pinsYFW
    What it is
    Zener diode
    Maker
    YFW
    Package
    SMC
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • CZRB5349B-HFSMBZener diode, 2 pins, ComchipZener diodeSMB2 pinsComchip
    What it is
    Zener diode
    Maker
    Comchip
    Package
    SMB
    Pins
    2
    Details
    12 V 5 mW zener diode
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • CZRC5349B-HFSMCZener diode, 2 pins, ComchipZener diodeSMC2 pinsComchip
    What it is
    Zener diode
    Maker
    Comchip
    Package
    SMC
    Pins
    2
    Details
    12 V 5 mW zener diode
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • SMB5349BSMBZener diode, 2 pins, DOWOZener diodeSMB2 pinsDOWO
    What it is
    Zener diode
    Maker
    DOWO
    Package
    SMB
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • SMBJ5349BSMBZener diode, 2 pins, Galaxy MicroelectronicsZener diodeSMB2 pinsGalaxy Microelectronics
    What it is
    Zener diode
    Maker
    Galaxy Microelectronics
    Package
    SMB
    Pins
    2
    Details
    12V, 10%, Surface Mount Zener Diodes
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • SMC5349BSMCZener diode, 2 pins, DOWOZener diodeSMC2 pinsDOWO
    What it is
    Zener diode
    Maker
    DOWO
    Package
    SMC
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • Z5SMC5349BSMCZener diode, 2 pins, Taitron ComponentsZener diodeSMC2 pinsTaitron Components
    What it is
    Zener diode
    Maker
    Taitron Components
    Package
    SMC
    Pins
    2
    Details
    SMD Zener Diodes (Two Terminals)- 5W
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • 1SMB5349SMBZener diode, 2 pins, First SilionZener diodeSMB2 pinsFirst Silion
    What it is
    Zener diode
    Maker
    First Silion
    Package
    SMB
    Pins
    2
    Details
    Zener diode: 11.40..12.60V, Zzt=3, Izt=100.0mA, 5W
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • 1SMB5349BSMBZener diode, 2 pins, Won-Top ElectronicsZener diodeSMB2 pinsWon-Top Electronics
    What it is
    Zener diode
    Maker
    Won-Top Electronics
    Package
    SMB
    Pins
    2
    Details
    Zener diode: 12V±5%, Izt=100mA, Zzt=2.5, 5W
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • AAT60039B-S16SOT-89Voltage supervisor, 3 pins, Advanced Analog TechnologyVoltage supervisorSOT-893 pinsAdvanced Analog Technology
    What it is
    Voltage supervisor
    Maker
    Advanced Analog Technology
    Package
    SOT-89
    Pins
    3
    Details
    Voltage detector IC: 3.9V±2%, -Reset PPO
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • ACZRC5349B-GSMCZener diode, 2 pins, ComchipZener diodeSMC2 pinsComchip
    What it is
    Zener diode
    Maker
    Comchip
    Package
    SMC
    Pins
    2
    Details
    Zener diode: 12.0V±5%, Izt=100mA, Zzt=2.5, 5W
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • AP8853-49BSOT-23LDO regulator, 3 pins, Anwell SemiconductorLDO regulatorSOT-233 pinsAnwell Semiconductor
    What it is
    LDO regulator
    Maker
    Anwell Semiconductor
    Package
    SOT-23
    Pins
    3
    Details
    Linear voltage regulator IC: LDO, 4.9V±2%, 300mA, Pb-free
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

  • CZRC5349B-GSMCZener diode, 2 pins, ComchipZener diodeSMC2 pinsComchip
    What it is
    Zener diode
    Maker
    Comchip
    Package
    SMC
    Pins
    2
    Details
    Zener diode: 12.0V±5%, Zzt=2.5, Izm=395mA, 5W
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

Zener diode

Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.

Working, it reads

About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • Open both ways, forward too: failed open.
  • Holds well off its rated voltage on the supply test: drifted.
  • A soft knee, or a voltage that creeps on the supply test: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Integrated circuit

Voltage with the board powered; ohms from each pin to ground with it off.

Working, it reads

Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.

Dead, it reads

  • A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  • Supply present, output stuck: failed, or its load has.
On the board:
A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
Compare:
The surest reference is the same IC on a working board, measured pin by pin.
Watch for:
Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Voltage regulator

Voltage, board powered, black probe on ground. Then ohms with the power off.

Working, it reads

Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.

Dead, it reads

  • Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
  • Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
  • Power off, input to output near 0 Ω: shorted.
On the board:
An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
Compare:
The same regulator on another rail or another board shows the right voltages and the right resistances.
Watch for:
Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Codes that begin with 349B

For a marking with its end worn or burnt off. Each code has a page of its own.

Did you find your part?

Open this in the search to correct a character or try another package.