Skip to content

SMD code 35 in SOD-323

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

Not sure which one you have?

Answer up to 4 quick questions and these 35 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • BZX384-A15SOD-323Zener diode, 2 pins, NexperiaZener diode2 pinsNexperia
    What it is
    Zener diode
    Maker
    Nexperia
    Package
    SOD-323
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • LUDZS13BT1GSOD-323Zener diode, 2 pins, LRCZener diode2 pinsLRC
    What it is
    Zener diode
    Maker
    LRC
    Package
    SOD-323
    Pins
    2
    Details
    Zener diode, VZ Min 12.91 V, VZ Nom 13.2 V, VZ Max 13.49 V
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • S-LUDZS13BT1GSOD-323Zener diode, 2 pins, LRCZener diode2 pinsLRC
    What it is
    Zener diode
    Maker
    LRC
    Package
    SOD-323
    Pins
    2
    Details
    Zener diode, VZ Min 12.91 V, VZ Nom 13.2 V, VZ Max 13.49 V
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • UDZ13BSOD-323Zener diode, 2 pins, Formosa MicrosemiZener diode2 pinsFormosa Microsemi
    What it is
    Zener diode
    Maker
    Formosa Microsemi
    Package
    SOD-323
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • UDZV13BSOD-323Zener diode, 2 pins, ROHMZener diode2 pinsROHM
    What it is
    Zener diode
    Maker
    ROHM
    Package
    SOD-323
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • UDZVFH13BSOD-323Zener diode, 2 pins, ROHMZener diode2 pinsROHM
    What it is
    Zener diode
    Maker
    ROHM
    Package
    SOD-323
    Pins
    2
    Details
    Zener Diode (AEC-Q101 qualified)
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • FDZ13VT1GSOD-323Zener diode, 2 pins, First SilionZener diode2 pinsFirst Silion
    What it is
    Zener diode
    Maker
    First Silion
    Package
    SOD-323
    Pins
    2
    Details
    Zener diode: 12.910..13.490V, Izt=5mA, Zzt=37, 200mW
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • GDZ2V7B-V-GSOD-323Zener diode, 2 pins, VishayZener diode2 pinsVishay
    What it is
    Zener diode
    Maker
    Vishay
    Package
    SOD-323
    Pins
    2
    Details
    Zener diode: 2.69..2.91V, Izt=5mA, Zzt=110, 200mW
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • HMSZ5235BSOD-3232 pins, Hi-Sincerity MicroelectronicsNot recorded2 pinsHi-Sincerity Microelectronics
    What it is
    Not recorded
    Maker
    Hi-Sincerity Microelectronics
    Package
    SOD-323
    Pins
    2
    Details
    Z-diode: 6.8V±5%, Izt=20mA, Zzt=5Ω, 225mW
    Source
    Published code list

    Is it dead? The meter test is below: Silicon diode.

  • UDZS13BSOD-323Zener diode, 2 pins, ROHMZener diode2 pinsROHM
    What it is
    Zener diode
    Maker
    ROHM
    Package
    SOD-323
    Pins
    2
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • ZD5235BS2SOD-323Zener diode, 2 pins, CtcZener diode2 pinsCtc
    What it is
    Zener diode
    Maker
    Ctc
    Package
    SOD-323
    Pins
    2
    Details
    6.8 V zener diode
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • 4 more parts have no package on record. Nothing rules them out, so they stay.
    • BFCN-1445+RF filter, Mini-CircuitsRF filterNot recordedMini-Circuits
      What it is
      RF filter
      Maker
      Mini-Circuits
      Package
      Not recorded
      Pins
      Not recorded
      Details
      LTCC filter, 1420-1470 MHz
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: This part.

    • FDG6335NN-channel MOSFET, onsemiN-channel MOSFETNot recordedonsemi
      What it is
      N-channel MOSFET
      Maker
      onsemi
      Package
      Not recorded
      Pins
      Not recorded
      Details
      MOSFET - N-Channel, POWERTRENCH
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: N-channel MOSFET.

    • MM5Z3V3BZener diode, Formosa MicrosemiZener diodeNot recordedFormosa Microsemi
      What it is
      Zener diode
      Maker
      Formosa Microsemi
      Package
      Not recorded
      Pins
      Not recorded
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Zener diode.

    • MM5Z3V3B-Q1Zener diode, Formosa MicrosemiZener diodeNot recordedFormosa Microsemi
      What it is
      Zener diode
      Maker
      Formosa Microsemi
      Package
      Not recorded
      Pins
      Not recorded
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Zener diode.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

Zener diode

Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.

Working, it reads

About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • Open both ways, forward too: failed open.
  • Holds well off its rated voltage on the supply test: drifted.
  • A soft knee, or a voltage that creeps on the supply test: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Silicon diode

Diode range, part lifted or one leg off the pad. Red probe on the anode.

Working, it reads

About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • Open both ways: failed open.
  • A reading the wrong way round as well: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

This part

Diode range and ohms range, part lifted.

Working, it reads

Depends on what it is. The datasheet, or an identical part, says.

Dead, it reads

  • Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
  • Open between every pair of pins: failed open, or a part that reads open when working.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

N-channel MOSFET

Diode range, part lifted. Test drain to source first, then short gate to source and test again.

Working, it reads

Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.

Dead, it reads

  • Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  • The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
  • No body diode at all: failed open.
On the board
the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Printed with a code easy to misread as 35

One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.

Did you find your part?

Open this in the search to correct a character or try another package.