Skip to content

SMD code 359B

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

359B is a capacitor marking

3.5 pF

3.5 pF capacitor

35 followed by the multiplier 9, in picofarads: 3.5 pF. Printed this way on film and larger ceramic capacitors; small chip ceramics are usually not printed at all. B is the tolerance, ±0.1 pF.

Check it with a meter

Lift one end and measure it on a capacitance range. A good one reads close to 3.5 pF. In circuit the meter also sees everything connected across it, so the reading means little until it is out. A failed one usually reads near 0 Ω, or a steady low resistance, on the ohms range, often from a crack. On the board a shorted capacitor shorts its whole rail. A failed reading does not change what to fit: the marking still says 3.5 pF.

On a transistor or diode body (SMC, SMB, SMA), 359B is a part code instead. Those parts are listed below.

16 parts are printed 359B

Not sure which one you have?

Answer up to 4 quick questions and these 16 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • 1SMC5359SMCZener diode, 2 pins, PanjitZener diodeSMC2 pinsPanjit
    What it is
    Zener diode
    Maker
    Panjit
    Package
    SMC
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • 1SMC5359-AUSMCZener diode, 2 pins, PanjitZener diodeSMC2 pinsPanjit
    What it is
    Zener diode
    Maker
    Panjit
    Package
    SMC
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • 1SMC5359BSMCZener diode, 2 pins, YFWZener diodeSMC2 pinsYFW
    What it is
    Zener diode
    Maker
    YFW
    Package
    SMC
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • CZRB5359B-HFSMBZener diode, 2 pins, ComchipZener diodeSMB2 pinsComchip
    What it is
    Zener diode
    Maker
    Comchip
    Package
    SMB
    Pins
    2
    Details
    24 V 5 mW zener diode
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • CZRC5359B-HFSMCZener diode, 2 pins, ComchipZener diodeSMC2 pinsComchip
    What it is
    Zener diode
    Maker
    Comchip
    Package
    SMC
    Pins
    2
    Details
    24 V 5 mW zener diode
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • FDN359BNSOT-23N-channel MOSFET, 3 pins, UMWN-channel MOSFETSOT-233 pinsUMW
    What it is
    N-channel MOSFET
    Maker
    UMW
    Package
    SOT-23
    Pins
    3
    Details
    N-channel MOSFET, 30 V, 5.8 A
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: N-channel MOSFET.

  • SMB5359BSMBZener diode, 2 pins, DOWOZener diodeSMB2 pinsDOWO
    What it is
    Zener diode
    Maker
    DOWO
    Package
    SMB
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • SMBJ5359BSMBZener diode, 2 pins, Galaxy MicroelectronicsZener diodeSMB2 pinsGalaxy Microelectronics
    What it is
    Zener diode
    Maker
    Galaxy Microelectronics
    Package
    SMB
    Pins
    2
    Details
    24V, 10%, Surface Mount Zener Diodes
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • SMC5359BSMCZener diode, 2 pins, DOWOZener diodeSMC2 pinsDOWO
    What it is
    Zener diode
    Maker
    DOWO
    Package
    SMC
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • Z5SMC5359BSMCZener diode, 2 pins, Taitron ComponentsZener diodeSMC2 pinsTaitron Components
    What it is
    Zener diode
    Maker
    Taitron Components
    Package
    SMC
    Pins
    2
    Details
    SMD Zener Diodes (Two Terminals)- 5W
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • 1SMB5359SMBZener diode, 2 pins, First SilionZener diodeSMB2 pinsFirst Silion
    What it is
    Zener diode
    Maker
    First Silion
    Package
    SMB
    Pins
    2
    Details
    Zener diode: 22.80..25.20V, Zzt=4, Izt=50.0mA, 5W
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • 1SMB5359BSMBZener diode, 2 pins, Won-Top ElectronicsZener diodeSMB2 pinsWon-Top Electronics
    What it is
    Zener diode
    Maker
    Won-Top Electronics
    Package
    SMB
    Pins
    2
    Details
    Zener diode: 24V±5%, Izt=50mA, Zzt=3.5, 5W
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • ACZRC5359B-GSMCZener diode, 2 pins, ComchipZener diodeSMC2 pinsComchip
    What it is
    Zener diode
    Maker
    Comchip
    Package
    SMC
    Pins
    2
    Details
    Zener diode: 24.0V±5%, Izt=50mA, Zzt=3.5, 5W
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • CZRC5359B-GSMCZener diode, 2 pins, ComchipZener diodeSMC2 pinsComchip
    What it is
    Zener diode
    Maker
    Comchip
    Package
    SMC
    Pins
    2
    Details
    Zener diode: 24.0V±5%, Zzt=3.5, Izm=198mA, 5W
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • SZ359BSMAZener diode, 2 pins, EIC SemiconductorZener diodeSMA2 pinsEIC Semiconductor
    What it is
    Zener diode
    Maker
    EIC Semiconductor
    Package
    SMA
    Pins
    2
    Details
    Zener diode: 9.1V±5%, Izt=41.2mA, Zzt=4.0, 1.5W
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

Zener diode

Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.

Working, it reads

About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • Open both ways, forward too: failed open.
  • Holds well off its rated voltage on the supply test: drifted.
  • A soft knee, or a voltage that creeps on the supply test: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

N-channel MOSFET

Diode range, part lifted. Test drain to source first, then short gate to source and test again.

Working, it reads

Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.

Dead, it reads

  • Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  • The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
  • No body diode at all: failed open.
On the board
the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Did you find your part?

Open this in the search to correct a character or try another package.