SMD code 360
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
360 on a chip resistor
36 Ω
36 Ω resistor, 5%
36 followed by 0 zeros. Three digits is normally the 5% series. The same marking also reads as 36 pF on a capacitor or 36 µH on an inductor, and nothing in the code says which; the body of the part does.
Other readings of the same characters, most likely first
- 36 pF capacitor
- 36 µH inductor
Check it with a meter
Lift one end and measure across it. A good one reads 36 Ω within 5%. Measuring it in circuit reads the parallel combination of everything around it, which is almost always lower, never higher: well above 36 Ω on the board is a fault. Open, or well above 36 Ω, means it has failed: burnt, cracked or corroded. That does not change what to fit: the marking still says 36 Ω. A burnt resistor usually means the part it feeds drew too much, so find that before fitting a new one.
On a transistor or diode body (SOT-23-5, USP-6B, SOT-23), 360 is a part code instead. Those parts are listed below.
16 parts are printed 360
Not sure which one you have?
Answer up to 4 quick questions and these 16 parts are ranked, with a meter test that settles it. It works on a dead part too.
ACDBA360-HFSMASchottky diode, 2 pins, ComchipSchottky diodeSMA2 pinsComchip
- What it is
- Schottky diode
- Maker
- Comchip
- Package
- SMA
- Pins
- 2
- Details
- 60 V, 3 A Schottky barrier diode
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Schottky diode.
ACDBB360-HFSMBSchottky diode, 2 pins, ComchipSchottky diodeSMB2 pinsComchip
- What it is
- Schottky diode
- Maker
- Comchip
- Package
- SMB
- Pins
- 2
- Details
- 60 V, 3 A Schottky barrier diode
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Schottky diode.
ACDBC360-HFSMCSchottky diode, 2 pins, ComchipSchottky diodeSMC2 pinsComchip
- What it is
- Schottky diode
- Maker
- Comchip
- Package
- SMC
- Pins
- 2
- Details
- 60 V, 3 A Schottky barrier diode
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Schottky diode.
CDBA360-HFSMASchottky diode, 2 pins, ComchipSchottky diodeSMA2 pinsComchip
- What it is
- Schottky diode
- Maker
- Comchip
- Package
- SMA
- Pins
- 2
- Details
- 60 V, 3 A Schottky barrier diode
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Schottky diode.
CDBB360-HFSMBSchottky diode, 2 pins, ComchipSchottky diodeSMB2 pinsComchip
- What it is
- Schottky diode
- Maker
- Comchip
- Package
- SMB
- Pins
- 2
- Details
- 60 V, 3 A Schottky barrier diode
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Schottky diode.
CDBC360-HFSMCSchottky diode, 2 pins, ComchipSchottky diodeSMC2 pinsComchip
- What it is
- Schottky diode
- Maker
- Comchip
- Package
- SMC
- Pins
- 2
- Details
- 60 V, 3 A Schottky barrier diode
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Schottky diode.
FDN360PSOT-23P-channel MOSFET, 3 pins, onsemiP-channel MOSFETSOT-233 pinsonsemi
- What it is
- P-channel MOSFET
- Maker
- onsemi
- Package
- SOT-23
- Pins
- 3
- Details
- MOSFET - Single, P-Channel, POWERTRENCH
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: P-channel MOSFET.
XC6104B231MRSOT-23-5Voltage supervisor, 5 pins, TorexVoltage supervisorSOT-23-55 pinsTorex
- What it is
- Voltage supervisor
- Maker
- Torex
- Package
- SOT-23-5
- Pins
- 5
- Details
- CMOS-IC: VDet 3.1V, 5%, Hst, ±Reset PPO, Wt=50ms, Rt=25ms
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
XC6203P312FRSOT-223TorexNot recordedSOT-223Not recordedTorex
- What it is
- Not recorded
- Maker
- Torex
- Package
- SOT-223
- Pins
- Not recorded
- Details
- VR-IC: Int. current limiter, 3.1V±2%, 400mA
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
XC6203P312MRSOT-233 pins, TorexNot recordedSOT-233 pinsTorex
- What it is
- Not recorded
- Maker
- Torex
- Package
- SOT-23
- Pins
- 3
- Details
- VR-IC: Int. current limiter, 3.1V±2%, 400mA
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
XC6203P312PRSOT-893 pins, TorexNot recordedSOT-893 pinsTorex
- What it is
- Not recorded
- Maker
- Torex
- Package
- SOT-89
- Pins
- 3
- Details
- VR-IC: Int. current limiter, 3.1V±2%, 400mA
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
XC6372E601PSOT-89-5DC-DC converter, 5 pins, TorexDC-DC converterSOT-89-55 pinsTorex
- What it is
- DC-DC converter
- Maker
- Torex
- Package
- SOT-89-5
- Pins
- 5
- Details
- DC/DC voltage converter IC: PWM/PFM st-up, 100kHz, 6.0V±2.5%, 100mA, int. Vdd
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
3 more parts have no package on record
ATF-360774 pins, BroadcomNot recordedNot recorded4 pinsBroadcom
- What it is
- Not recorded
- Maker
- Broadcom
- Package
- Not recorded
- Pins
- 4
- Details
- 2–18 GHz Ultra Low Noise Pseudomorphic HEMT
- Source
- Published code list
Is it dead? The meter test is below: This part.
HZM3.6NBZener diode, RenesasZener diodeNot recordedNot recordedRenesas
- What it is
- Zener diode
- Maker
- Renesas
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Z-diode: 3.4..3.8V, 200mW
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
VRH3601NVLDO regulator, AnaSemLDO regulatorNot recordedNot recordedAnaSem
- What it is
- LDO regulator
- Maker
- AnaSem
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Linear voltage regulator IC: LDO, 3.6V±1%, 250mA, +CE
- Source
- Published code list
Is it dead? The meter test is below: Voltage regulator.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
Schottky diode
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- A reading the wrong way round as well: leaky.
- Open both ways: failed open.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
P-channel MOSFET
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the drain, black on the source: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
- Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
- The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
- No body diode at all: failed open.
- On the board
- the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. Lift a leg to be sure.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
This part
Diode range and ohms range, part lifted.
Working, it reads
Depends on what it is. The datasheet, or an identical part, says.
Dead, it reads
- Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
- Open between every pair of pins: failed open, or a part that reads open when working.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Zener diode
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways, forward too: failed open.
- Holds well off its rated voltage on the supply test: drifted.
- A soft knee, or a voltage that creeps on the supply test: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage regulator
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
- Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
- Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
- Power off, input to output near 0 Ω: shorted.
- On the board:
- An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
- Compare:
- The same regulator on another rail or another board shows the right voltages and the right resistances.
- Watch for:
- Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Integrated circuit
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
- A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
- Supply present, output stuck: failed, or its load has.
- On the board:
- A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
- Compare:
- The surest reference is the same IC on a working board, measured pin by pin.
- Watch for:
- Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed with a code easy to misread as 360
One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.
Codes not listed here are printed on 2 more parts.
Did you find your part?
Open this in the search to correct a character or try another package.