SMD marking

44in SOT-323

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables.

3 parts are printed 44

Not sure which one you have?

Answer up to 4 quick questions and these 3 parts are ranked, with a meter test that settles it. It works on a dead part too.

BAT54SWSOT-323Schottky diode, NexperiaSchottky diodeNexperia
What it is
Schottky diode
Maker
Nexperia
Package
SOT-323
Pins
3
Details
30 V surface-mount Schottky barrier diode, dual series
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
A reading the wrong way round as well: leaky.
Open both ways: failed open.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor BAT54SW, opens in a new tab
PDTA124XUSOT-323Digital transistor (PNP, resistors built in), NexperiaDigital transistor (PNP, resistors built in)Nexperia
What it is
Digital transistor (PNP, resistors built in)
Maker
Nexperia
Package
SOT-323
Pins
3
Details
PNP resistor-equipped transistor; R1 = 22 kΩ, R2 = 47 kΩ
Source
From the manufacturer's datasheet
Is it dead?
Ohms range, part lifted. The datasheet gives the built-in resistors: R1 in series with the base, R2 from base to emitter.
Working, it reads
Base to emitter reads about R1 plus R2 either way round, about 20 kΩ on a 10 k and 10 k part, give or take their wide tolerance. Collector to emitter reads open. A part with no R2 reads a junction behind R1 one way instead.
Dead, it reads
Collector to emitter the same both ways, near 0 Ω with a continuous beep: shorted.
From the base, open or far above R1 plus R2: R1 has failed. Static damage shows here most often.
Base to emitter near 0 Ω: failed short.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
The readings depend on the resistor values, so an identical part elsewhere on the board is the surest reference. Measure it the same way.
Watch for:
On the diode range a good part with 10 kΩ resistors reads open on every pair, so a good part looks dead there. Use the ohms range.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PDTA124XU, opens in a new tab
1 more part has no package on record. Nothing rules them out, so they stay.
- BB664InfineonNot recordedInfineon
  What it is
  Not recorded
  Maker
  Infineon
  Package
  Not recorded
  Pins
  Not recorded
  Source
  From the manufacturer's datasheet
  Is it dead?
  Diode range and ohms range, part lifted.
  Working, it reads
  Depends on what it is. The datasheet, or an identical part, says.
  Dead, it reads
  Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
  Open between every pair of pins: failed open, or a part that reads open when working.
  On the board:
  On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
  Compare:
  If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
  A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
  Datasheetfor BB664, opens in a new tab

22 more parts have codes that begin with 44

Codes that begin with 44

For a marking with its end worn or burnt off. Each one shows its full printed code.

all Panjit. What differs:

PB4413-DFAprinted 443AESD protection diodeESD protection diode
Printed 443A. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
ESD protection diode
Maker
Panjit
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PB4413-DFA, opens in a new tab
PB4415-DFAprinted 445AESD protection diodeESD protection diode
Printed 445A. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
ESD protection diode
Maker
Panjit
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
A reading both ways on a one-way part: leaky.
A one-way part open both ways: failed open.
On the board:
On the board, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PB4415-DFA, opens in a new tab
PJ4L40W6printed 441Schottky diodeSchottky diode
Printed 441. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
Schottky diode
Maker
Panjit
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted or one leg off the pad. Red probe on the anode.
Working, it reads
About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.
Dead, it reads
The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
A reading the wrong way round as well: leaky.
Open both ways: failed open.
On the board:
On the board this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJ4L40W6, opens in a new tab
PJQ4403P-AUprinted 4403MOSFETMOSFET
Printed 4403. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJQ4403P-AU, opens in a new tab
PJQ4411Pprinted 4411MOSFETMOSFET
Printed 4411. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJQ4411P, opens in a new tab
PJQ4427DPprinted 4427MOSFETMOSFET
Printed 4427. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJQ4427DP, opens in a new tab
PJQ4441P-AUprinted 4441MOSFETMOSFET
Printed 4441. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJQ4441P-AU, opens in a new tab
PJQ4442Pprinted 4442MOSFETMOSFET
Printed 4442. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJQ4442P, opens in a new tab
PJQ4442P-AUprinted 4442MOSFETMOSFET
Printed 4442. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJQ4442P-AU, opens in a new tab
PJQ4443P-AUprinted 4443MOSFETMOSFET
Printed 4443. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJQ4443P-AU, opens in a new tab
PJQ4453P-AUprinted 4453MOSFETMOSFET
Printed 4453. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJQ4453P-AU, opens in a new tab
PJQ4460AP-AUprinted 4460MOSFETMOSFET
Printed 4460. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJQ4460AP-AU, opens in a new tab
PJQ4463AP-AUprinted 4463MOSFETMOSFET
Printed 4463. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJQ4463AP-AU, opens in a new tab
PJQ4464AP-AUprinted 4464MOSFETMOSFET
Printed 4464. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJQ4464AP-AU, opens in a new tab
PJQ4465APprinted 4465MOSFETMOSFET
Printed 4465. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJQ4465AP, opens in a new tab
PJQ4465AP-AUprinted 4465MOSFETMOSFET
Printed 4465. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJQ4465AP-AU, opens in a new tab
PJQ4468AP-AUprinted 4468MOSFETMOSFET
Printed 4468. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJQ4468AP-AU, opens in a new tab
PJQ4476APprinted 4476MOSFETMOSFET
Printed 4476. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJQ4476AP, opens in a new tab
PJQ44605AP-AUprinted 44605AMOSFETMOSFET
Printed 44605A. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJQ44605AP-AU, opens in a new tab
PJQ44607AP-AUprinted 44607AMOSFETMOSFET
Printed 44607A. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJQ44607AP-AU, opens in a new tab
PJQ44609AP-AUprinted 44609AMOSFETMOSFET
Printed 44609A. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJQ44609AP-AU, opens in a new tab
PJQ44611AP-AUprinted 44611AMOSFETMOSFET
Printed 44611A. Only the start matches what you typed, so this fits only if the rest of the marking is worn off.
What it is
MOSFET
Maker
Panjit
Package
Not recorded
Pins
Not recorded
Source
From the manufacturer's datasheet
Is it dead?
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.
Dead, it reads
Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
The gate reads low to source or drain: gate shorted.
No body diode at all: failed open.
On the board:
On the board the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Datasheetfor PJQ44611AP-AU, opens in a new tab

Open this in the search to correct a character or try another package.

3 parts are printed 44

Is it dead?

Is it dead?

Is it dead?

Codes that begin with 44

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?

Is it dead?