SMD code 560
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
560 on a chip resistor
56 Ω
56 Ω resistor, 5%
56 followed by 0 zeros. Three digits is normally the 5% series. The same marking also reads as 56 pF on a capacitor or 56 µH on an inductor, and nothing in the code says which; the body of the part does.
Other readings of the same characters, most likely first
- 56 pF capacitor
- 56 µH inductor
Check it with a meter
Lift one end and measure across it. A good one reads 56 Ω within 5%. Measuring it in circuit reads the parallel combination of everything around it, which is almost always lower, never higher: well above 56 Ω on the board is a fault. Open, or well above 56 Ω, means it has failed: burnt, cracked or corroded. That does not change what to fit: the marking still says 56 Ω. A burnt resistor usually means the part it feeds drew too much, so find that before fitting a new one.
On a transistor or diode body (SOT-23-5, SOT-23, SOT-89-5), 560 is a part code instead. Those parts are listed below.
19 parts are printed 560
Not sure which one you have?
Answer up to 4 quick questions and these 19 parts are ranked, with a meter test that settles it. It works on a dead part too.
S5KP60D2PAKTVS diode, 3 pins, EIC SemiconductorTVS diodeD2PAK3 pinsEIC Semiconductor
- What it is
- TVS diode
- Maker
- EIC Semiconductor
- Package
- D2PAK
- Pins
- 3
- Details
- Transient voltage supressor: Vbr=66.7..81.5V, Vrwm=60V, 47A, 5000W(1ms)
- Source
- Published code list
Is it dead? The meter test is below: TVS or ESD protection diode.
XC9111A601MRSOT-23DC-DC converter, 3 pins, TorexDC-DC converterSOT-233 pinsTorex
- What it is
- DC-DC converter
- Maker
- Torex
- Package
- SOT-23
- Pins
- 3
- Details
- DC/DC voltage converter IC: PFM st-up, 100kHz, 6.0V±2.5%, 400mA
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
XC9111A601PRSOT-89DC-DC converter, 3 pins, TorexDC-DC converterSOT-893 pinsTorex
- What it is
- DC-DC converter
- Maker
- Torex
- Package
- SOT-89
- Pins
- 3
- Details
- DC/DC voltage converter IC: PFM st-up, 100kHz, 6.0V±2.5%, 400mA
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
XC9111C601MRSOT-23-5DC-DC converter, 5 pins, TorexDC-DC converterSOT-23-55 pinsTorex
- What it is
- DC-DC converter
- Maker
- Torex
- Package
- SOT-23-5
- Pins
- 5
- Details
- DC/DC voltage converter IC: PFM st-up, 100kHz, 6.0V±2.5%, 400mA, +CE
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
TVS or ESD protection diode
Diode range, from the protected line to ground, part lifted if you can.
Working, it reads
A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.
Dead, it reads
- From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
- A reading both ways on a one-way part: leaky.
- A one-way part open both ways: failed open.
- On the board
- , a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
- Compare:
- The same part on the next line or connector pin is the healthy reading to compare with.
- Watch for:
- A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Integrated circuit
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
- A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
- Supply present, output stuck: failed, or its load has.
- On the board:
- A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
- Compare:
- The surest reference is the same IC on a working board, measured pin by pin.
- Watch for:
- Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Did you find your part?
Open this in the search to correct a character or try another package.