Skip to content

SMD code 589

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

589 on a chip capacitor

5.8 pF

5.8 pF capacitor

58 followed by the multiplier 9, in picofarads: 5.8 pF. Printed this way on film and larger ceramic capacitors; small chip ceramics are usually not printed at all.

Check it with a meter

Lift one end and measure it on a capacitance range. A good one reads close to 5.8 pF. In circuit the meter also sees everything connected across it, so the reading means little until it is out. A failed one usually reads near 0 Ω, or a steady low resistance, on the ohms range, often from a crack. On the board a shorted capacitor shorts its whole rail. A failed reading does not change what to fit: the marking still says 5.8 pF.

On a transistor or diode body (SOT-23, USP-6C, SOT-23-5), 589 is a part code instead. Those parts are listed below.

10 parts are printed 589

Not sure which one you have?

Answer up to 4 quick questions and these 10 parts are ranked, with a meter test that settles it. It works on a dead part too.

3 pins. What differs:

  • FMBT589SOT-23PNP transistor, Formosa MicrosemiPNP transistorSOT-23Formosa Microsemi
    What it is
    PNP transistor
    Maker
    Formosa Microsemi
    Package
    SOT-23
    Pins
    3
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: PNP transistor.

  • MMBT589SOT-23PNP transistor, Galaxy MicroelectronicsPNP transistorSOT-23Galaxy Microelectronics
    What it is
    PNP transistor
    Maker
    Galaxy Microelectronics
    Package
    SOT-23
    Pins
    3
    Details
    PNP bipolar transistor
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: PNP transistor.

  • MMBT589-HFSOT-23PNP transistor, ComchipPNP transistorSOT-23Comchip
    What it is
    PNP transistor
    Maker
    Comchip
    Package
    SOT-23
    Pins
    3
    Details
    -30 V, -0.6 A PNP transistor
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: PNP transistor.

  • PBSS5120TSOT-23PNP transistor, HXYPNP transistorSOT-23HXY
    What it is
    PNP transistor
    Maker
    HXY
    Package
    SOT-23
    Pins
    3
    Details
    Bipolar transistor, 30 V, 1 A
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: PNP transistor.

  • PBSS5120T,215SOT-23PNP transistor, HXYPNP transistorSOT-23HXY
    What it is
    PNP transistor
    Maker
    HXY
    Package
    SOT-23
    Pins
    3
    Details
    Bipolar transistor, 30 V, 1 A
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: PNP transistor.

  • CHT589PTSOT-23PNP transistor, Chenmko EnterprisePNP transistorSOT-23Chenmko Enterprise
    What it is
    PNP transistor
    Maker
    Chenmko Enterprise
    Package
    SOT-23
    Pins
    3
    Details
    PNP transistor: AF, Sw, 30V, 1A, B=100..300, 100MHz
    Source
    Published code list

    Is it dead? The meter test is below: PNP transistor.

  • FMMT589SOT-23Diodes IncorporatedNot recordedSOT-23Diodes Incorporated
    What it is
    Not recorded
    Maker
    Diodes Incorporated
    Package
    SOT-23
    Pins
    3
    Details
    pnp 30V 1A
    Source
    Published code list

    Is it dead? The meter test is below: This part.

  • FMMT589ASOT-23Diodes IncorporatedNot recordedSOT-23Diodes Incorporated
    What it is
    Not recorded
    Maker
    Diodes Incorporated
    Package
    SOT-23
    Pins
    3
    Details
    pnp 30V 1A
    Source
    Published code list

    Is it dead? The meter test is below: This part.

  • XC6502402MSOT-23LDO regulator, TorexLDO regulatorSOT-23Torex
    What it is
    LDO regulator
    Maker
    Torex
    Package
    SOT-23
    Pins
    3
    Details
    Linear voltage regulator IC: LDO, 4.0V±2%, 200mA
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

  • XC6502402PSOT-89LDO regulator, TorexLDO regulatorSOT-89Torex
    What it is
    LDO regulator
    Maker
    Torex
    Package
    SOT-89
    Pins
    3
    Details
    Linear voltage regulator IC: LDO, 4.0V±2%, 200mA
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

PNP transistor

Diode range, part lifted or its base leg off the pad.

Working, it reads

Black probe on the base reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.

Dead, it reads

  • Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
  • The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
  • Only one junction reads, or none: a junction has failed open. It then looks like a diode.
  • A reading the wrong way round, where it should be open: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

This part

Diode range and ohms range, part lifted.

Working, it reads

Depends on what it is. The datasheet, or an identical part, says.

Dead, it reads

  • Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
  • Open between every pair of pins: failed open, or a part that reads open when working.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Voltage regulator

Voltage, board powered, black probe on ground. Then ohms with the power off.

Working, it reads

Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.

Dead, it reads

  • Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
  • Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
  • Power off, input to output near 0 Ω: shorted.
On the board:
An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
Compare:
The same regulator on another rail or another board shows the right voltages and the right resistances.
Watch for:
Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Printed with a code easy to misread as 589

One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.

Codes that begin with 589

For a marking with its end worn or burnt off. Each code has a page of its own.

Did you find your part?

Open this in the search to correct a character or try another package.