SMD code 623
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
623 on a chip resistor
62 kΩ
62 kΩ resistor, 5%
62 followed by 3 zeros. Three digits is normally the 5% series. The same marking also reads as 62 nF on a capacitor, and nothing in the code says which; the body of the part does.
Other readings of the same characters, most likely first
- 62 nF capacitor
Check it with a meter
Lift one end and measure across it. A good one reads 62 kΩ within 5%. Measuring it in circuit reads the parallel combination of everything around it, which is almost always lower, never higher: well above 62 kΩ on the board is a fault. Open, or well above 62 kΩ, means it has failed: burnt, cracked or corroded. That does not change what to fit: the marking still says 62 kΩ. A burnt resistor usually means the part it feeds drew too much, so find that before fitting a new one.
On a transistor or diode body (SOT-23-5, SOT-23, SON), 623 is a part code instead. Those parts are listed below.
16 parts are printed 623
Not sure which one you have?
Answer up to 4 quick questions and these 16 parts are ranked, with a meter test that settles it. It works on a dead part too.
EC880623C5SOT-353LDO regulator, 5 pins, E-CMOSLDO regulatorSOT-3535 pinsE-CMOS
- What it is
- LDO regulator
- Maker
- E-CMOS
- Package
- SOT-353
- Pins
- 5
- Details
- Linear voltage regulator IC: LDO, 2.3V±2%, 300mA, +CE
- Source
- Published code list
Is it dead? The meter test is below: Voltage regulator.
ELM990731ACSOT-89LDO regulator, 3 pins, ELM TechnologyLDO regulatorSOT-893 pinsELM Technology
- What it is
- LDO regulator
- Maker
- ELM Technology
- Package
- SOT-89
- Pins
- 3
- Details
- Linear voltage regulator IC: LDO, 7.3V±2%, 300mA
- Source
- Published code list
Is it dead? The meter test is below: Voltage regulator.
IXD2111B231MRSOT-23DC-DC converter, 3 pins, IXYSDC-DC converterSOT-233 pinsIXYS
- What it is
- DC-DC converter
- Maker
- IXYS
- Package
- SOT-23
- Pins
- 3
- Details
- DC/DC voltage converter IC: PFM st-up, 100kHz, 2.3V±2.5%, 400mA
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
IXD2111B231PRSOT-89DC-DC converter, 3 pins, IXYSDC-DC converterSOT-893 pinsIXYS
- What it is
- DC-DC converter
- Maker
- IXYS
- Package
- SOT-89
- Pins
- 3
- Details
- DC/DC voltage converter IC: PFM st-up, 100kHz, 2.3V±2.5%, 400mA
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
IXD2111D231MRSOT-23-5DC-DC converter, 5 pins, IXYSDC-DC converterSOT-23-55 pinsIXYS
- What it is
- DC-DC converter
- Maker
- IXYS
- Package
- SOT-23-5
- Pins
- 5
- Details
- DC/DC voltage converter IC: PFM st-up, 100kHz, 2.3V±2.5%, 400mA, +CE
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
PZM6.2NB3SOT-233 pins, NexperiaNot recordedSOT-233 pinsNexperia
- What it is
- Not recorded
- Maker
- Nexperia
- Package
- SOT-23
- Pins
- 3
- Details
- 6.2V 0.3W zener
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
R1114N231DSOT-23-55 pins, Nisshinbo Micro DevicesNot recordedSOT-23-55 pinsNisshinbo Micro Devices
- What it is
- Not recorded
- Maker
- Nisshinbo Micro Devices
- Package
- SOT-23-5
- Pins
- 5
- Details
- VR-IC: LDO, LN, CE, auto discharge, 2,3V±2%, 150mA
- Source
- Published code list
Is it dead? The meter test is below: Voltage regulator.
R1191N023DSOT-23-5LDO regulator, 5 pins, RicohLDO regulatorSOT-23-55 pinsRicoh
- What it is
- LDO regulator
- Maker
- Ricoh
- Package
- SOT-23-5
- Pins
- 5
- Details
- Linear voltage regulator IC: LDO, 2.3V±1.5%, 300mA, +CE, ECO, CL
- Source
- Published code list
Is it dead? The meter test is below: Voltage regulator.
XC9111B231MRSOT-23DC-DC converter, 3 pins, TorexDC-DC converterSOT-233 pinsTorex
- What it is
- DC-DC converter
- Maker
- Torex
- Package
- SOT-23
- Pins
- 3
- Details
- DC/DC voltage converter IC: PFM st-up, 100kHz, 2.3V±2.5%, 400mA
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
XC9111B231PRSOT-89DC-DC converter, 3 pins, TorexDC-DC converterSOT-893 pinsTorex
- What it is
- DC-DC converter
- Maker
- Torex
- Package
- SOT-89
- Pins
- 3
- Details
- DC/DC voltage converter IC: PFM st-up, 100kHz, 2.3V±2.5%, 400mA
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
XC9111D231MRSOT-23-5DC-DC converter, 5 pins, TorexDC-DC converterSOT-23-55 pinsTorex
- What it is
- DC-DC converter
- Maker
- Torex
- Package
- SOT-23-5
- Pins
- 5
- Details
- DC/DC voltage converter IC: PFM st-up, 100kHz, 2.3V±2.5%, 400mA, +CE
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
4 more parts have no package on record
FDMA6023PZTDual P-channel MOSFET, onsemiDual P-channel MOSFETNot recordedNot recordedonsemi
- What it is
- Dual P-channel MOSFET
- Maker
- onsemi
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Dual P-Channel PowerTrench MOSFET
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: P-channel MOSFET pair.
1PMT4623Zener diode, Microsemi Integrated Products DivisionZener diodeNot recordedNot recordedMicrosemi Integrated Products Division
- What it is
- Zener diode
- Maker
- Microsemi Integrated Products Division
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Zener diode: 4.3V±5%, Izt=168.4mA, 1W
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
HZM6.2NB3Zener diode, RenesasZener diodeNot recordedNot recordedRenesas
- What it is
- Zener diode
- Maker
- Renesas
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Z-diode: 6.26..6.53V, 200mW
- Source
- Published code list
Is it dead? The meter test is below: Zener diode.
KIC7623T5Voltage supervisor, KECVoltage supervisorNot recordedNot recordedKEC
- What it is
- Voltage supervisor
- Maker
- KEC
- Package
- Not recorded
- Pins
- Not recorded
- Details
- Voltage detector IC: 2.3V±1%, -Reset ODO
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
P-channel MOSFET pair
Diode range, part lifted. Test drain to source first, then short gate to source and test again. Test each MOSFET on its own pins, as the datasheet's pinout gives them.
Working, it reads
Red probe on the drain, black on the source: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
- Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
- The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
- No body diode at all: failed open.
- On the board
- the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. Lift a leg to be sure.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Zener diode
Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.
Working, it reads
About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.
Dead, it reads
- The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
- Open both ways, forward too: failed open.
- Holds well off its rated voltage on the supply test: drifted.
- A soft knee, or a voltage that creeps on the supply test: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Voltage regulator
Voltage, board powered, black probe on ground. Then ohms with the power off.
Working, it reads
Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.
Dead, it reads
- Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
- Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
- Power off, input to output near 0 Ω: shorted.
- On the board:
- An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
- Compare:
- The same regulator on another rail or another board shows the right voltages and the right resistances.
- Watch for:
- Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Integrated circuit
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
- A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
- Supply present, output stuck: failed, or its load has.
- On the board:
- A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
- Compare:
- The surest reference is the same IC on a working board, measured pin by pin.
- Watch for:
- Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed with a code easy to misread as 623
One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.
Did you find your part?
Open this in the search to correct a character or try another package.