SMD code 692I
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
4 parts are printed 692I
Not sure which one you have?
Answer up to 4 quick questions and these 4 parts are ranked, with a meter test that settles it. It works on a dead part too.
G692H308T1UfSOT-23-55 pins, Global Mixed-mode TechnologySOT-23-55 pinsGlobal Mixed-mode Technology
- What it is
- Voltage supervisor
- Maker
- Global Mixed-mode Technology
- Package
- SOT-23-5
- Pins
- 5
- Details
- 4-Pin µP Voltage Monitors with Manual Reset Input
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Integrated circuit.
G692H308TCUfSOT-1434 pins, Global Mixed-mode TechnologySOT-1434 pinsGlobal Mixed-mode Technology
- What it is
- Voltage supervisor
- Maker
- Global Mixed-mode Technology
- Package
- SOT-143
- Pins
- 4
- Details
- 4-Pin µP Voltage Monitors with Manual Reset Input
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: Integrated circuit.
LTC692IS8SOIC-88 pins, Analog DevicesSOIC-88 pinsAnalog Devices
- What it is
- Not recorded
- Maker
- Analog Devices
- Package
- SOIC-8
- Pins
- 8
- Details
- equivalent LTC692IN8
- Source
- Published code list
Is it dead? The meter test is below: This part.
SS8039H308TCSOT-1434 pins, Silicon StandardSOT-1434 pinsSilicon Standard
- What it is
- Voltage supervisor
- Maker
- Silicon Standard
- Package
- SOT-143
- Pins
- 4
- Details
- Voltage detector IC: 3.08V±1.5%, +Reset PPO, -MR
- Source
- Published code list
Is it dead? The meter test is below: Integrated circuit.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
Integrated circuit
Voltage with the board powered; ohms from each pin to ground with it off.
Working, it reads
Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.
Dead, it reads
- A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
- Supply present, output stuck: failed, or its load has.
- On the board:
- A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
- Compare:
- The surest reference is the same IC on a working board, measured pin by pin.
- Watch for:
- Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
This part
Diode range and ohms range, part lifted.
Working, it reads
Depends on what it is. The datasheet, or an identical part, says.
Dead, it reads
- Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
- Open between every pair of pins: failed open, or a part that reads open when working.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Printed with a code easy to misread as 692I
One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.
Did you find your part?
Open this in the search to correct a character or try another package.