Skip to content

SMD code 72

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

Not sure which one you have?

Answer up to 4 quick questions and these 50 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • 1PS70SB20SOT-323Schottky diode, 3 pins, NexperiaSchottky diodeSOT-3233 pinsNexperia
    What it is
    Schottky diode
    Maker
    Nexperia
    Package
    SOT-323
    Pins
    3
    Details
    Schottky barrier single diode
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Schottky diode.

  • 2N7002SOT-883N-channel MOSFET, 3 pins, LeiditechN-channel MOSFETSOT-8833 pinsLeiditech
    What it is
    N-channel MOSFET
    Maker
    Leiditech
    Package
    SOT-883
    Pins
    3
    Details
    60V, N Channel, Small Signal MOSFETs
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: N-channel MOSFET.

  • 2N7002HLSOT-883N-channel MOSFET, 3 pins, Galaxy MicroelectronicsN-channel MOSFETSOT-8833 pinsGalaxy Microelectronics
    What it is
    N-channel MOSFET
    Maker
    Galaxy Microelectronics
    Package
    SOT-883
    Pins
    3
    Details
    60V, N Channel, Small Signal MOSFETs
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: N-channel MOSFET.

  • 2N7002HMSOT-723N-channel MOSFET, 3 pins, Galaxy MicroelectronicsN-channel MOSFETSOT-7233 pinsGalaxy Microelectronics
    What it is
    N-channel MOSFET
    Maker
    Galaxy Microelectronics
    Package
    SOT-723
    Pins
    3
    Details
    60V, N Channel, Small Signal MOSFETs
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: N-channel MOSFET.

  • 2N7002HM-HFSOT-723N-channel MOSFET, 3 pins, ComchipN-channel MOSFETSOT-7233 pinsComchip
    What it is
    N-channel MOSFET
    Maker
    Comchip
    Package
    SOT-723
    Pins
    3
    Details
    60 V, 0.3 A N-channel MOSFET
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: N-channel MOSFET.

  • 2N7002KCTSOT-723N-channel MOSFET, 3 pins, Yangjie Electronic TechN-channel MOSFETSOT-7233 pinsYangjie Electronic Tech
    What it is
    N-channel MOSFET
    Maker
    Yangjie Electronic Tech
    Package
    SOT-723
    Pins
    3
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: N-channel MOSFET.

  • 2N7002TSOT-523MOSFET, 3 pins, Galaxy MicroelectronicsMOSFETSOT-5233 pinsGalaxy Microelectronics
    What it is
    MOSFET
    Maker
    Galaxy Microelectronics
    Package
    SOT-523
    Pins
    3
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: MOSFET.

  • A2N7002HL-HFSOT-883N-channel MOSFET, 3 pins, ComchipN-channel MOSFETSOT-8833 pinsComchip
    What it is
    N-channel MOSFET
    Maker
    Comchip
    Package
    SOT-883
    Pins
    3
    Details
    60 V, 0.3 A N-channel MOSFET
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: N-channel MOSFET.

  • BZX84-B20SOT-23Zener diode, 3 pins, NexperiaZener diodeSOT-233 pinsNexperia
    What it is
    Zener diode
    Maker
    Nexperia
    Package
    SOT-23
    Pins
    3
    Pinout
    • 1 anode
    • 2 not connected
    • 3 cathode
    Details
    20 V ±2% voltage regulator (Zener) diode
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • EDZV3.9BSOD-523Zener diode, 2 pins, ROHMZener diodeSOD-5232 pinsROHM
    What it is
    Zener diode
    Maker
    ROHM
    Package
    SOD-523
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • EDZVFH3.9BSOD-523Zener diode, 2 pins, ROHMZener diodeSOD-5232 pinsROHM
    What it is
    Zener diode
    Maker
    ROHM
    Package
    SOD-523
    Pins
    2
    Details
    Zener Diode (AEC-Q101 qualified)
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • ESD1285WPDFN1610-2ESD protection diode, 2 pins, LeiditechESD protection diodeDFN1610-22 pinsLeiditech
    What it is
    ESD protection diode
    Maker
    Leiditech
    Package
    DFN1610-2
    Pins
    2
    Details
    ESD protection diode, VRWM 11 V, Cj 250 pF
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • ESD7002WTSOT-323ESD protection diode, 3 pins, onsemiESD protection diodeSOT-3233 pinsonsemi
    What it is
    ESD protection diode
    Maker
    onsemi
    Package
    SOT-323
    Pins
    3
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • L2N7002M3T5GSOT-723N-channel MOSFET, 3 pins, LRCN-channel MOSFETSOT-7233 pinsLRC
    What it is
    N-channel MOSFET
    Maker
    LRC
    Package
    SOT-723
    Pins
    3
    Details
    MOSFET, N-Channel, VDSS 60 V, VGS 20 V
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: N-channel MOSFET.

  • 1 more part has no package on record

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

Schottky diode

Diode range, part lifted or one leg off the pad. Red probe on the anode.

Working, it reads

About 0.15 to 0.45 V anode to cathode, roughly half a silicon diode, and open the other way.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • A reading the wrong way round as well: leaky.
  • Open both ways: failed open.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A large Schottky can read about 0.1 V forward and beep like a short, and leaks a little the wrong way when good, more when warm. It is shorted only if it reads the same both ways. Measure it cold, beside an identical cold one.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

N-channel MOSFET

Diode range, part lifted. Test drain to source first, then short gate to source and test again.

Working, it reads

Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.

Dead, it reads

  • Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  • The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
  • No body diode at all: failed open.
On the board
the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

MOSFET

Diode range, part lifted. Test drain to source first, then short gate to source and test again.

Working, it reads

One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.

Dead, it reads

  • Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  • The gate reads low to source or drain: gate shorted.
  • No body diode at all: failed open.
On the board
the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Zener diode

Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.

Working, it reads

About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • Open both ways, forward too: failed open.
  • Holds well off its rated voltage on the supply test: drifted.
  • A soft knee, or a voltage that creeps on the supply test: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

TVS or ESD protection diode

Diode range, from the protected line to ground, part lifted if you can.

Working, it reads

A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.

Dead, it reads

  • From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  • A reading both ways on a one-way part: leaky.
  • A one-way part open both ways: failed open.
On the board
, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Printed with a code easy to misread as 72

One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.

Codes not listed here are printed on 3 more parts.

Did you find your part?

Open this in the search to correct a character or try another package.