Skip to content

SMD code 75C

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

75C on a chip resistor

59 kΩ

59 kΩ resistor, 1%

EIA-96 precision code: 75 stands for 590 in the E96 table, and the letter C is the multiplier, × 100. These are 1% parts.

Check it with a meter

Lift one end and measure across it. A good one reads 59 kΩ within 1%. Measuring it in circuit reads the parallel combination of everything around it, which is almost always lower, never higher: well above 59 kΩ on the board is a fault. Open, or well above 59 kΩ, means it has failed: burnt, cracked or corroded. That does not change what to fit: the marking still says 59 kΩ. A burnt resistor usually means the part it feeds drew too much, so find that before fitting a new one.

On a transistor or diode body (SOT-23-5, SOT-89, SOT-89-5), 75C is a part code instead. Those parts are listed below.

Not sure which one you have?

Answer up to 4 quick questions and these 34 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • P4SMAJ75CSMATVS diode, 2 pins, Sunmate SemiconductorTVS diodeSMA2 pinsSunmate Semiconductor
    What it is
    TVS diode
    Maker
    Sunmate Semiconductor
    Package
    SMA
    Pins
    2
    Details
    TVS: 75V, 3A, 400W (1ms), Bidirectional
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • P4SMFJ75CSOD-123FTVS diode, 2 pins, YeashinTVS diodeSOD-123F2 pinsYeashin
    What it is
    TVS diode
    Maker
    Yeashin
    Package
    SOD-123F
    Pins
    2
    Details
    Transient voltage supressor: Vrwm=75V, Ipp=3A, 400W (1ms), Bidir.
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • P6SMBJ75CSMBTVS diode, 2 pins, LittelfuseTVS diodeSMB2 pinsLittelfuse
    What it is
    TVS diode
    Maker
    Littelfuse
    Package
    SMB
    Pins
    2
    Details
    TVS: 67.5..82.5V, 5.5A, 600W(1ms), Bidirectional
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • PSMAJ75CASMATVS diode, 2 pins, Lite-On SemiconductorTVS diodeSMA2 pinsLite-On Semiconductor
    What it is
    TVS diode
    Maker
    Lite-On Semiconductor
    Package
    SMA
    Pins
    2
    Details
    Transient voltage supressor: Vrwm=64.7V, Vbr=71.3..78.8V, Ipp=3.9A, 400W(1ms), Bidir.
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • PSMBJ75CASMBTVS diode, 2 pins, Lite-On SemiconductorTVS diodeSMB2 pinsLite-On Semiconductor
    What it is
    TVS diode
    Maker
    Lite-On Semiconductor
    Package
    SMB
    Pins
    2
    Details
    Transient voltage supressor: Vrwm=64.7V, Vbr=71.3..78.8V, Ipp=5.8A, 600W(1ms), Bidir.
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • PSMCJ75CASMCTVS diode, 2 pins, Lite-On SemiconductorTVS diodeSMC2 pinsLite-On Semiconductor
    What it is
    TVS diode
    Maker
    Lite-On Semiconductor
    Package
    SMC
    Pins
    2
    Details
    Transient voltage supressor: Vrwm=64.7V, Vbr=71.3..78.8V, Ipp=14.6A, 1500W(1ms), Bidir.
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • SMAJP4KE75CASMATVS diode, 2 pins, Micro Commercial ComponentsTVS diodeSMA2 pinsMicro Commercial Components
    What it is
    TVS diode
    Maker
    Micro Commercial Components
    Package
    SMA
    Pins
    2
    Details
    Transient voltage supressor: Vrwm=64.10V, Vbr=71.30..78.80V, Ipp=4.0A, 400W(1ms), Bidir.
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • SMBG75CSMBG2 pins, Microsemi Integrated Products DivisionNot recordedSMBG2 pinsMicrosemi Integrated Products Division
    What it is
    Not recorded
    Maker
    Microsemi Integrated Products Division
    Package
    SMBG
    Pins
    2
    Details
    TVS: 75V, 4.5A, 600W(1ms), Bidirectional
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • SMBJP6KE75CASMBTVS diode, 2 pins, Micro Commercial ComponentsTVS diodeSMB2 pinsMicro Commercial Components
    What it is
    TVS diode
    Maker
    Micro Commercial Components
    Package
    SMB
    Pins
    2
    Details
    Transient voltage supressor: Vrwm=64.10V, Vbr=71.30..78.80V, Ipp=5.9A, 600W(1ms), Bidir.
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • SMCJ1.5KE75CASMCTVS diode, 2 pins, Micro Commercial ComponentsTVS diodeSMC2 pinsMicro Commercial Components
    What it is
    TVS diode
    Maker
    Micro Commercial Components
    Package
    SMC
    Pins
    2
    Details
    Transient voltage supressor: Vrwm=64.10V, Vbr=71.30..78.80V, Ipp=14.8A, 1500W(1ms), Bidir.
    Source
    Published code list

    Is it dead? The meter test is below: TVS or ESD protection diode.

  • TSH75CDSOIC-1616 pins, SGS-Thomson MicroelectronicsNot recordedSOIC-1616 pinsSGS-Thomson Microelectronics
    What it is
    Not recorded
    Maker
    SGS-Thomson Microelectronics
    Package
    SOIC-16
    Pins
    16
    Details
    Op-IC: Quad, WB, LP, St-by, ±5V, 70MHz
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • TSH75CD/CDTSOIC-1616 pins, STMicroelectronicsNot recordedSOIC-1616 pinsSTMicroelectronics
    What it is
    Not recorded
    Maker
    STMicroelectronics
    Package
    SOIC-16
    Pins
    16
    Source
    Published code list

    Is it dead? The meter test is below: This part.

  • TSH75CDTSOIC-1616 pins, STMicroelectronicsNot recordedSOIC-1616 pinsSTMicroelectronics
    What it is
    Not recorded
    Maker
    STMicroelectronics
    Package
    SOIC-16
    Pins
    16
    Details
    Op-IC: Quad, WB, LP, St-by, ±5V, 70MHz
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

  • TSH75CPTTSSOP-1616 pins, STMicroelectronicsNot recordedTSSOP-1616 pinsSTMicroelectronics
    What it is
    Not recorded
    Maker
    STMicroelectronics
    Package
    TSSOP-16
    Pins
    16
    Source
    Published code list

    Is it dead? The meter test is below: This part.

  • TSH75PTTSSOP-1616 pins, SGS-Thomson MicroelectronicsNot recordedTSSOP-1616 pinsSGS-Thomson Microelectronics
    What it is
    Not recorded
    Maker
    SGS-Thomson Microelectronics
    Package
    TSSOP-16
    Pins
    16
    Details
    Op-IC: Quad, WB, LP, St-by, ±5V, 70MHz
    Source
    Published code list

    Is it dead? The meter test is below: Integrated circuit.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

TVS or ESD protection diode

Diode range, from the protected line to ground, part lifted if you can.

Working, it reads

A one-way part reads about 0.6 to 0.8 V forward and open in reverse. A two-way part reads open both ways. Arrays with several lines read as the datasheet's diagram draws them.

Dead, it reads

  • From the line to ground, the same reading both ways, near 0 V with a continuous beep: shorted.
  • A reading both ways on a one-way part: leaky.
  • A one-way part open both ways: failed open.
On the board
, a line reading shorted to ground can be this part or anything else on that line. Lift it: if the short goes with it, it has failed.
Compare:
The same part on the next line or connector pin is the healthy reading to compare with.
Watch for:
A two-way part reads open both ways when it is good, exactly like one that has failed open. The meter cannot tell them apart; an identical part on the next line can.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Integrated circuit

Voltage with the board powered; ohms from each pin to ground with it off.

Working, it reads

Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.

Dead, it reads

  • A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  • Supply present, output stuck: failed, or its load has.
On the board:
A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
Compare:
The surest reference is the same IC on a working board, measured pin by pin.
Watch for:
Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

This part

Diode range and ohms range, part lifted.

Working, it reads

Depends on what it is. The datasheet, or an identical part, says.

Dead, it reads

  • Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
  • Open between every pair of pins: failed open, or a part that reads open when working.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Did you find your part?

Open this in the search to correct a character or try another package.