Skip to content

SMD code 84K

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

84K on a chip resistor

84 kΩ

84 kΩ resistor

The K is both the decimal point and the multiplier: 84 kΩ.

Check it with a meter

Lift one end and measure across it. A good one reads 84 kΩ. Measuring it in circuit reads the parallel combination of everything around it, which is almost always lower, never higher: well above 84 kΩ on the board is a fault. Open, or well above 84 kΩ, means it has failed: burnt, cracked or corroded. That does not change what to fit: the marking still says 84 kΩ. A burnt resistor usually means the part it feeds drew too much, so find that before fitting a new one.

On a transistor or diode body (SOT-23-5, SOT-89, SOT-89-5), 84K is a part code instead. Those parts are listed below.

Not sure which one you have?

Answer up to 4 quick questions and these 25 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • BSS84KSOT-23P-channel MOSFET, 3 pins, JSCJP-channel MOSFETSOT-233 pinsJSCJ
    What it is
    P-channel MOSFET
    Maker
    JSCJ
    Package
    SOT-23
    Pins
    3
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: P-channel MOSFET.

  • BSS84KW-P2-HFSOT-323P-channel MOSFET, 3 pins, ComchipP-channel MOSFETSOT-3233 pinsComchip
    What it is
    P-channel MOSFET
    Maker
    Comchip
    Package
    SOT-323
    Pins
    3
    Details
    -50 V, -0.13 A P-channel MOSFET
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: P-channel MOSFET.

  • FMBSS84K-Q1-HSOT-23MOSFET, 3 pins, Formosa MicrosemiMOSFETSOT-233 pinsFormosa Microsemi
    What it is
    MOSFET
    Maker
    Formosa Microsemi
    Package
    SOT-23
    Pins
    3
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: MOSFET.

  • FMOSBSS84KWSOT-323MOSFET, 3 pins, Formosa MicrosemiMOSFETSOT-3233 pinsFormosa Microsemi
    What it is
    MOSFET
    Maker
    Formosa Microsemi
    Package
    SOT-323
    Pins
    3
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: MOSFET.

  • FMOSBSS84KW-Q1SOT-323MOSFET, 3 pins, Formosa MicrosemiMOSFETSOT-3233 pinsFormosa Microsemi
    What it is
    MOSFET
    Maker
    Formosa Microsemi
    Package
    SOT-323
    Pins
    3
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: MOSFET.

  • GSFK0501ESOT-363Dual P-channel MOSFET, 6 pins, Good-ArkDual P-channel MOSFETSOT-3636 pinsGood-Ark
    What it is
    Dual P-channel MOSFET
    Maker
    Good-Ark
    Package
    SOT-363
    Pins
    6
    Details
    Dual P-channel MOSFET, 50 V
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: P-channel MOSFET pair.

  • WM05P02FSOT-8833 pins, WayonNot recordedSOT-8833 pinsWayon
    What it is
    Not recorded
    Maker
    Wayon
    Package
    SOT-883
    Pins
    3
    Details
    MOSFET
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: MOSFET.

  • IXD1701BA8ERUSP-6C6 pins, IXYSNot recordedUSP-6C6 pinsIXYS
    What it is
    Not recorded
    Maker
    IXYS
    Package
    USP-6C
    Pins
    6
    Details
    Linear voltage regulator IC: 10.8V±2%, 150mA, +CE
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

  • IXD1701BA8MRSOT-23-55 pins, IXYSNot recordedSOT-23-55 pinsIXYS
    What it is
    Not recorded
    Maker
    IXYS
    Package
    SOT-23-5
    Pins
    5
    Details
    Linear voltage regulator IC: 10.8V±2%, 150mA, +CE
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

  • IXD1701BA8PRSOT-89-55 pins, IXYSNot recordedSOT-89-55 pinsIXYS
    What it is
    Not recorded
    Maker
    IXYS
    Package
    SOT-89-5
    Pins
    5
    Details
    Linear voltage regulator IC: 10.8V±2%, 150mA, +CE
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

  • IXD1701D18FRSOT-223IXYSNot recordedSOT-223Not recordedIXYS
    What it is
    Not recorded
    Maker
    IXYS
    Package
    SOT-223
    Pins
    Not recorded
    Details
    Linear voltage regulator IC: 1.8V±2%, 150mA
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

  • IXD1701D18JRDPAK3 pins, IXYSNot recordedDPAK3 pinsIXYS
    What it is
    Not recorded
    Maker
    IXYS
    Package
    DPAK
    Pins
    3
    Details
    Linear voltage regulator IC: 1.8V±2%, 150mA
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

  • IXD1701D18PRSOT-893 pins, IXYSNot recordedSOT-893 pinsIXYS
    What it is
    Not recorded
    Maker
    IXYS
    Package
    SOT-89
    Pins
    3
    Details
    Linear voltage regulator IC: 1.8V±2%, 150mA
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

  • MCP1804T-1802I/DBSOT-223LDO regulator, MicrochipLDO regulatorSOT-223Not recordedMicrochip
    What it is
    LDO regulator
    Maker
    Microchip
    Package
    SOT-223
    Pins
    Not recorded
    Details
    Linear voltage regulator IC: LDO, 1.8V±2%, 150mA
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

  • MCP1804T-1802I/MBSOT-89LDO regulator, 3 pins, MicrochipLDO regulatorSOT-893 pinsMicrochip
    What it is
    LDO regulator
    Maker
    Microchip
    Package
    SOT-89
    Pins
    3
    Details
    Linear voltage regulator IC: LDO, 1.8V±2%, 150mA
    Source
    Published code list

    Is it dead? The meter test is below: Voltage regulator.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

P-channel MOSFET

Diode range, part lifted. Test drain to source first, then short gate to source and test again.

Working, it reads

Red probe on the drain, black on the source: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.

Dead, it reads

  • Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  • The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
  • No body diode at all: failed open.
On the board
the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

MOSFET

Diode range, part lifted. Test drain to source first, then short gate to source and test again.

Working, it reads

One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.

Dead, it reads

  • Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  • The gate reads low to source or drain: gate shorted.
  • No body diode at all: failed open.
On the board
the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

P-channel MOSFET pair

Diode range, part lifted. Test drain to source first, then short gate to source and test again. Test each MOSFET on its own pins, as the datasheet's pinout gives them.

Working, it reads

Red probe on the drain, black on the source: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.

Dead, it reads

  • Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  • The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
  • No body diode at all: failed open.
On the board
the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Voltage regulator

Voltage, board powered, black probe on ground. Then ohms with the power off.

Working, it reads

Input pin at the supply, output pin at its rated voltage, and the enable pin high if it has one.

Dead, it reads

  • Output equal to the input: the pass element has shorted. Everything after it may have taken the full input.
  • Input present, enable high, no output: failed open, or holding itself off into a shorted load. Power off and measure output to ground.
  • Power off, input to output near 0 Ω: shorted.
On the board:
An output at 0 V is often a shorted load with the regulator in current limit. Lift the output pin: if the short stays on the board, the regulator may be fine.
Compare:
The same regulator on another rail or another board shows the right voltages and the right resistances.
Watch for:
Makers put input, output and ground on different pins in the same package, so take them from this part's datasheet. Diode or ohms readings between its pins say little; check it powered.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Printed with a code easy to misread as 84K

One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.

Did you find your part?

Open this in the search to correct a character or try another package.