Skip to content

SMD code 916A

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

916A on a chip capacitor

91 µF, 10 V

91 µF, 10 V tantalum capacitor

A moulded tantalum capacitor: 916 is the capacitance in picofarads (91 µF) and A is the rated-voltage code (10 V).

Check it with a meter

Lift one end and measure it on a capacitance range. A good one reads close to 91 µF. In circuit the meter also sees everything connected across it, so the reading means little until it is out. It is polarised: the band on the body marks the positive end, and a tantalum fitted backwards fails short, sometimes with a flame. A failed tantalum usually reads near 0 Ω both ways, often with a burnt or cracked body. A failed reading does not change what to fit: the marking still says 91 µF, 10 V. Fit the same capacitance at the same or a higher voltage.

On a transistor or diode body (SMA, SMB, SMC), 916A is a part code instead. Those parts are listed below.

10 parts are printed 916A

Not sure which one you have?

Answer up to 4 quick questions and these 10 parts are ranked, with a meter test that settles it. It works on a dead part too.

Zener diode, 2 pins. What differs:

  • 1.5SMA5916ASMAGood-ArkSMAGood-Ark
    What it is
    Zener diode
    Maker
    Good-Ark
    Package
    SMA
    Pins
    2
    Details
    Zener diode, VZ 4.3 V, 1.5 W
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • 1SMA5916-AUSMAPanjitSMAPanjit
    What it is
    Zener diode
    Maker
    Panjit
    Package
    SMA
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • 1SMA5916ASMAHXYSMAHXY
    What it is
    Zener diode
    Maker
    HXY
    Package
    SMA
    Pins
    2
    Details
    Zener diode, 12 V, 0.0312 A
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • PMAZ4V3BSMAPrisemiSMAPrisemi
    What it is
    Zener diode
    Maker
    Prisemi
    Package
    SMA
    Pins
    2
    Details
    Zener diode, 4.3 V, 1 V
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • S-SMA5916ASMALeiditechSMALeiditech
    What it is
    Zener diode
    Maker
    Leiditech
    Package
    SMA
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • ZGFM5916B-AFSMAFFormosa MicrosemiSMAFFormosa Microsemi
    What it is
    Zener diode
    Maker
    Formosa Microsemi
    Package
    SMAF
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • ZGFM5916B-AF-Q1SMAFFormosa MicrosemiSMAFFormosa Microsemi
    What it is
    Zener diode
    Maker
    Formosa Microsemi
    Package
    SMAF
    Pins
    2
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Zener diode.

  • 1SMA5916SMAPanjitSMAPanjit
    What it is
    Zener diode
    Maker
    Panjit
    Package
    SMA
    Pins
    2
    Details
    Zener diode: 4.3V±10%, Zzt=6, Izm<349mA, 1.5W
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • 1SMB5916ASMBEIC SemiconductorSMBEIC Semiconductor
    What it is
    Zener diode
    Maker
    EIC Semiconductor
    Package
    SMB
    Pins
    2
    Details
    Z-diode: 4,3V±10%, Izt=87,2mA, Zzt=6Ω, 3W
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

  • Z1.5SMA5916BSMATaitron ComponentsSMATaitron Components
    What it is
    Zener diode
    Maker
    Taitron Components
    Package
    SMA
    Pins
    2
    Details
    Zener diode: 4.09..4.52V, Izt=87.2mA, 1.5W
    Source
    Published code list

    Is it dead? The meter test is below: Zener diode.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

Zener diode

Diode range for the forward check, part lifted, red probe on the anode. A bench supply for the Zener voltage.

Working, it reads

About 0.6 to 0.8 V forward and open in reverse on the diode range. Its Zener voltage shows only on a supply: feed it through a resistor that sets about 5 mA, cathode to positive, read quickly, and it should hold near its rated voltage.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • Open both ways, forward too: failed open.
  • Holds well off its rated voltage on the supply test: drifted.
  • A soft knee, or a voltage that creeps on the supply test: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A meter's diode range stops at about 2 to 3 V, so almost every Zener reads open in reverse on it, good or bad; a 3 V meter may just show a 2.4 or 2.7 V part. Above about 3 V the meter cannot tell a Zener from a plain diode.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Printed with a code easy to misread as 916A

One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.

Did you find your part?

Open this in the search to correct a character or try another package.