SMD code 9435
Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.
4 parts are printed 9435
Not sure which one you have?
Answer up to 4 quick questions and these 4 parts are ranked, with a meter test that settles it. It works on a dead part too.
AO9435SOIC-8P-channel MOSFET, 8 pins, HottechP-channel MOSFETSOIC-88 pinsHottech
- What it is
- P-channel MOSFET
- Maker
- Hottech
- Package
- SOIC-8
- Pins
- 8
- Details
- P-channel MOSFET, 30 V
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: P-channel MOSFET.
MMJT9435SOT-223PNP transistor, 4 pins, onsemiPNP transistorSOT-2234 pinsonsemi
- What it is
- PNP transistor
- Maker
- onsemi
- Package
- SOT-223
- Pins
- 4
- Details
- Bipolar Power Transistors
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: PNP transistor.
SM9435PSKSOIC-8P-channel MOSFET, 8 pins, Sinopower SemiconductorP-channel MOSFETSOIC-88 pinsSinopower Semiconductor
- What it is
- P-channel MOSFET
- Maker
- Sinopower Semiconductor
- Package
- SOIC-8
- Pins
- 8
- Details
- 30 V, 5.4 A P-channel MOSFET
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: P-channel MOSFET.
BRCS9435SCSOIC-8P-channel MOSFET, 8 pins, Blue RocketP-channel MOSFETSOIC-88 pinsBlue Rocket
- What it is
- P-channel MOSFET
- Maker
- Blue Rocket
- Package
- SOIC-8
- Pins
- 8
- Source
- Manufacturer datasheet
Is it dead? The meter test is below: P-channel MOSFET.
Is it dead? One meter test per kind
Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.
P-channel MOSFET
Diode range, part lifted. Test drain to source first, then short gate to source and test again.
Working, it reads
Red probe on the drain, black on the source: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.
Dead, it reads
- Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
- The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
- No body diode at all: failed open.
- On the board
- the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. Lift a leg to be sure.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
PNP transistor
Diode range, part lifted or its base leg off the pad.
Working, it reads
Black probe on the base reads about 0.6 to 0.75 V to the emitter and to the collector, and open the other way round. Collector to emitter reads open both ways.
Dead, it reads
- Collector to emitter the same both ways, near 0 V with a continuous beep: shorted. The commonest failure.
- The base the same both ways to another pin, near 0 V or a middling value: a shorted junction.
- Only one junction reads, or none: a junction has failed open. It then looks like a diode.
- A reading the wrong way round, where it should be open: leaky.
- On the board
- this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
- Compare:
- If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
- Watch for:
- A pair of diodes with a common pin reads just like a transistor, and some transistors carry a built-in diode or resistor. The datasheet says which.
A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.
Codes that begin with 9435
For a marking with its end worn or burnt off. Each code has a page of its own.
Did you find your part?
Open this in the search to correct a character or try another package.