Skip to content

SMD code A04 in SOT-23

Marking codes are not standardised, and the same code is reused by unrelated makers for unrelated parts. Below is every part in our tables printed with it, and any printed with a code that is easy to misread as it, from the manufacturers' own marking tables and published code lists.

7 parts in SOT-23 are printed A04

Not sure which one you have?

Answer up to 4 quick questions and these 15 parts are ranked, with a meter test that settles it. It works on a dead part too.

  • AP10TN135NSOT-23N-channel MOSFET, 3 pins, Advanced Power ElectronicsN-channel MOSFET3 pinsAdvanced Power Electronics
    What it is
    N-channel MOSFET
    Maker
    Advanced Power Electronics
    Package
    SOT-23
    Pins
    3
    Details
    100 V, 2.1 A N-channel MOSFET
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: N-channel MOSFET.

  • MMBD1204SOT-23Switching diode, 3 pins, Galaxy MicroelectronicsSwitching diode3 pinsGalaxy Microelectronics
    What it is
    Switching diode
    Maker
    Galaxy Microelectronics
    Package
    SOT-23
    Pins
    3
    Details
    0.6A, 100V, Surface Mount Small Signal Switching Diodes
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: Silicon diode.

  • PJA3404SOT-23MOSFET, 3 pins, PanjitMOSFET3 pinsPanjit
    What it is
    MOSFET
    Maker
    Panjit
    Package
    SOT-23
    Pins
    3
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: MOSFET.

  • PJA3404-AUSOT-23MOSFET, 3 pins, PanjitMOSFET3 pinsPanjit
    What it is
    MOSFET
    Maker
    Panjit
    Package
    SOT-23
    Pins
    3
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: MOSFET.

  • SI2304ASOT-23N-channel MOSFET, 3 pins, UMWN-channel MOSFET3 pinsUMW
    What it is
    N-channel MOSFET
    Maker
    UMW
    Package
    SOT-23
    Pins
    3
    Details
    N-channel MOSFET, 30 V, 5.8 A
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: N-channel MOSFET.

  • SM2304NSASOT-23N-channel MOSFET, 3 pins, Sinopower SemiconductorN-channel MOSFET3 pinsSinopower Semiconductor
    What it is
    N-channel MOSFET
    Maker
    Sinopower Semiconductor
    Package
    SOT-23
    Pins
    3
    Details
    30 V, 5.1 A N-channel MOSFET
    Source
    Manufacturer datasheet

    Is it dead? The meter test is below: N-channel MOSFET.

  • SST204SOT-233 pins, Calogic CorporationNot recorded3 pinsCalogic Corporation
    What it is
    Not recorded
    Maker
    Calogic Corporation
    Package
    SOT-23
    Pins
    3
    Details
    n-FET: AF, LN, 25V, 350mW, Idss=0.2..3mA, Up<2V
    Source
    Published code list

    Is it dead? The meter test is below: MOSFET.

  • 8 more parts have no package on record. Nothing rules them out, so they stay.
    • SM2404NSANN-channel MOSFET, Sinopower SemiconductorN-channel MOSFETNot recordedSinopower Semiconductor
      What it is
      N-channel MOSFET
      Maker
      Sinopower Semiconductor
      Package
      Not recorded
      Pins
      Not recorded
      Details
      30 V, 5.1 A N-channel MOSFET
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: N-channel MOSFET.

    • U74AHC1G04Logic gate, UnisonicLogic gateNot recordedUnisonic
      What it is
      Logic gate
      Maker
      Unisonic
      Package
      Not recorded
      Pins
      Not recorded
      Source
      Manufacturer datasheet

      Is it dead? The meter test is below: Integrated circuit.

    • 74AHC1G04GVNXPNot recordedNot recordedNXP
      What it is
      Not recorded
      Maker
      NXP
      Package
      Not recorded
      Pins
      Not recorded
      Details
      CMOS logic IC: Single inverter
      Source
      Published code list

      Is it dead? The meter test is below: Integrated circuit.

    • 74AHC3G04DCNXPNot recordedNot recordedNXP
      What it is
      Not recorded
      Maker
      NXP
      Package
      Not recorded
      Pins
      Not recorded
      Details
      CMOS logic IC: Triple inverter
      Source
      Published code list

      Is it dead? The meter test is below: Integrated circuit.

    • 74AHC3G04DPNXPNot recordedNot recordedNXP
      What it is
      Not recorded
      Maker
      NXP
      Package
      Not recorded
      Pins
      Not recorded
      Details
      CMOS logic IC: Triple inverter
      Source
      Published code list

      Is it dead? The meter test is below: Integrated circuit.

    • 74AHC3G04GDNXPNot recordedNot recordedNXP
      What it is
      Not recorded
      Maker
      NXP
      Package
      Not recorded
      Pins
      Not recorded
      Details
      CMOS logic IC: Triple inverter
      Source
      Published code list

      Is it dead? The meter test is below: Integrated circuit.

    • MAR4Mini-CircuitsNot recordedNot recordedMini-Circuits
      What it is
      Not recorded
      Maker
      Mini-Circuits
      Package
      Not recorded
      Pins
      Not recorded
      Details
      MMIC amp to 1GHz
      Source
      Published code list

      Is it dead? The meter test is below: RF amplifier.

    • MSA-04864 pins, BroadcomNot recorded4 pinsBroadcom
      What it is
      Not recorded
      Maker
      Broadcom
      Package
      Not recorded
      Pins
      4
      Source
      Published code list

      Is it dead? The meter test is below: This part.

Is it dead? One meter test per kind

Parts of the same kind are tested the same way, so each test is here once. Each part above points to its own.

N-channel MOSFET

Diode range, part lifted. Test drain to source first, then short gate to source and test again.

Working, it reads

Red probe on the source, black on the drain: about 0.4 to 0.9 V, the body diode. Open the other way. The gate reads open to both other pins, both ways.

Dead, it reads

  • Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  • The gate reads low to source or drain: gate shorted. Often all three pins end up shorted together.
  • No body diode at all: failed open.
On the board
the gate usually has a resistor to the source, so gate to source reads that resistor, which is not a fault. A drain short can be the load. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Silicon diode

Diode range, part lifted or one leg off the pad. Red probe on the anode.

Working, it reads

About 0.5 to 0.8 V anode to cathode, and open the other way. Small switching diodes read about 0.6 to 0.7 V; large rectifiers can read a little lower.

Dead, it reads

  • The same reading both ways round, near 0 V with a continuous beep or the same middling value: shorted.
  • Open both ways: failed open.
  • A reading the wrong way round as well: leaky.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
A three-pin body can hold two diodes. With a common pin they read two junctions from that pin, just like a transistor; in series they read two drops end to end. Test each pair the datasheet names.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

MOSFET

Diode range, part lifted. Test drain to source first, then short gate to source and test again.

Working, it reads

One way between drain and source reads about 0.4 to 0.9 V, the body diode, and the other way open. The gate reads open to both other pins.

Dead, it reads

  • Drain to source the same both ways, near 0 V with a continuous beep, and still so after shorting gate to source: shorted. The classic failure.
  • The gate reads low to source or drain: gate shorted.
  • No body diode at all: failed open.
On the board
the gate usually has a resistor to the source, which reads as that resistor and is not a fault. Lift a leg to be sure.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The diode range can charge the gate enough to turn the part on, and then drain to source reads near 0 both ways on a good part. Short gate to source and test again before you condemn it.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Integrated circuit

Voltage with the board powered; ohms from each pin to ground with it off.

Working, it reads

Supply pin at its voltage and the output doing what the datasheet says. Readings between pins depend on the part.

Dead, it reads

  • A pin near 0 Ω to ground or to the supply pin where an identical part does not read that: failed short.
  • Supply present, output stuck: failed, or its load has.
On the board:
A pin shorted to ground on the board can be anything on that net. Lift the pin to be sure.
Compare:
The surest reference is the same IC on a working board, measured pin by pin.
Watch for:
Its protection diodes can read like junctions between pins, even like a transistor. That proves nothing either way.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

RF amplifier

Voltage, board powered, on the output pin that the bias resistor or choke feeds.

Working, it reads

The output pin sits at the device voltage the datasheet gives, a few volts, below the supply.

Dead, it reads

  • Output pin at 0 V, or near 0 Ω to ground with the power off: shorted inside.
  • Output pin at the full supply voltage: open inside, no current flowing.
On the board:
Measured on the board with power on; the bias network is part of the reading.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.
Watch for:
The figures depend on the part and its bias resistor. The datasheet gives both.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

This part

Diode range and ohms range, part lifted.

Working, it reads

Depends on what it is. The datasheet, or an identical part, says.

Dead, it reads

  • Between two pins, the same reading both ways, near 0 V with a continuous beep: shorted.
  • Open between every pair of pins: failed open, or a part that reads open when working.
On the board
this is a first look only: the meter reads every path between those pins, and a short can be a neighbour. Lift one leg before you condemn it.
Compare:
If an identical part sits elsewhere on the board, measure it the same way: that is what this one should read.

A dead part still carries its marking. A short or an open says it has failed, not that it is a different part.

Printed with a code easy to misread as A04

One character differs, and it is one that is easy to confuse under a lamp. Each code has a page of its own.

Codes that begin with A04

For a marking with its end worn or burnt off. Each code has a page of its own.

Did you find your part?

Open this in the search to correct a character or try another package.